GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The throttle position (TP) is compared to an expected throttle position based on engine load. The engine control module (ECM) determines engine load based on inputs from the mass air flow (MAF) and the manifold absolute pressure (MAP) sensors. If the ECM detects that the current load and throttle position are not consistent with the expected load and throttle position, DTC P0068 is set.

Conditions for Running the DTC

    • DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0121, P0122, P0123, P0221, P0222, P0223 are not set.
    •  The engine speed is more than 600 RPM and less than 6,300 RPM.

Conditions for Setting the DTC

The ECM detects that the throttle position and indicated engine load do not correspond with the expected load and throttle position.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records.
    • The control module commands the TAC system to operate in the Reduced Engine Power mode.
    • A message center or an indicator displays Reduced Engine Power.
    • Under certain conditions the control module commands the engine OFF.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Step

Action

Value(s)

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

Are DTCs P0121, P0122, P0123, P0221, P0222, P0223, P0101, P0102, P0103, P0106, P0107, P0108 also set?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

Go to Step 3

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Intermittent Conditions

4

Inspect for the following conditions:

    • Vacuum hoses for splits, kinks, and proper connections as shown on Vehicle Emission Control Information label
    • Any type of leak or restriction
    • Air leaks at the throttle body mounting area and the intake manifold sealing surfaces
    • Restrictions in the air intake system, including filter

Did you find and correct the condition?

--

Go to Step 12

Go to Step 5

5

Important: Observe the TP sensors 1 and 2 angle parameter with a scan tool.

  1. Start the engine.
  2. Apply accelerator pedal slightly and record TP 1 and 2 angles.
  3. Turn OFF the ignition.

Is the difference between TP sensor 1 angle and TP sensor 2 angle less than the specified value?

3%

Go to Step 10

Go to Step 6

6

Test the throttle position (TP) sensor 1 5-volt reference circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 7

7

Test the TP sensor low reference circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 8

8

Test the TP sensor 1 signal circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

9

Test the TP sensor 2 signal circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

10

Inspect the throttle body for the following conditions:

    • A loose or damaged throttle blade
    • A broken throttle shaft

Did you find a condition?

--

Go to Step 11

--

11

Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 3

Go to Step 13

13

Important: More than one throttle actuator control (TAC) system-related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Be aware of this when reviewing Captured Info.

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK