Important: Before performing any panel adjustment procedures, refer to Folding Top Clearance Gap Specifications .

Important: Before making adjustments to the up/down position of the rear compartment lid, determine which panel needs the adjustment and for what reason.

1. Place the folding top in the down position.

Place a protective covering over the interior of the vehicle and the adjacent body panels.

2. Open the rear compartment.



3. Loosen the nuts (3) from the rear compartment lid (1).
4. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.

Notice: Refer to Fastener Notice in the Preface section.

5. Adjust the lid as necessary.

Tighten
Tighten the nuts to 11 N·m (97 lb in).

6. Close the lid.
7. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
8. Repeat the adjustment procedure as necessary.
9. Remove the protective covering.
10. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .

The cross car position of the rear compartment is determined by the 2 cross car bumpers (1), one on each side of the rear compartment lid. Each bumper contacts a non-adjustable bracket (2), that is mounted to the longitudinal frame support of the folding top. Both of the bumpers must contact these brackets when the rear compartment lid is closed.

1. Place the folding top in the down position.
2. Measure the gaps on both sides of the rear compartment lid. Determine the direction and amount of adjustment required. Refer to Folding Top Clearance Gap Specifications .
3. Open the rear compartment.
4. Place a protective covering over the interior and the adjacent body panels.



5. Loosen the cross car bumper nuts (1) on the rear compartment lid.
6. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.

Notice: Refer to Fastener Notice in the Preface section.

7. Adjust the bumpers as necessary.

Tighten
Tighten the nuts to 11 N·m (97 lb in).

8. Close the rear compartment.
9. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
10. Repeat the adjustment procedure as necessary.
11. Remove the protective covering.
12. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .

The cross car position of the rear compartment is determined by the 2 cross car bumpers (1), one on each side of the rear compartment lid. Each bumper contacts a non-adjustable bracket (2), that is mounted to the longitudinal frame support of the folding top. Both of the bumpers must contact these brackets when the rear compartment lid is closed.

1. Place the folding top in the down position.
2. Measure the gaps on both sides of the rear compartment lid. Determine the direction and amount of adjustment required. Refer to Folding Top Clearance Gap Specifications .
3. Open the rear compartment.
4. Place a protective covering over the interior and the adjacent body panels.



5. Loosen the cross car bumper jamb nuts.

Notice: Refer to Fastener Notice in the Preface section.

6. Adjust the bumpers (1) as necessary.

Tighten
Tighten the jamb nuts to 10 N·m (89 lb in).

7. Close the rear compartment.
8. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
9. Repeat the adjustment procedure as necessary.
10. Remove the protective covering.
11. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .

1. Place the folding top in the down position.
2. Place a protective covering over the interior of the vehicle and the adjacent body panels.
3. Open the rear compartment.



4. Loosen the jam nuts from the rubber bumper (2) on the quarter panel.

Notice: Refer to Fastener Notice in the Preface section.

5. Adjust the rubber bumpers (2) up or down to obtain the necessary adjustment.

Tighten
Tighten the jam nuts to 10 N·m (89 lb in).

6. Close the rear compartment.
7. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
8. Repeat the adjustment procedure as necessary.
9. Remove the protective covering.
10. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .

1. Place the folding top in the down position.

Place a protective covering over the interior of the vehicle and the adjacent body panels.

2. Open the rear compartment.



3. Loosen the jam nuts from the rear compartment lid bumper (1).

Notice: Refer to Fastener Notice in the Preface section.

4. Adjust the rubber bumpers (1) up or down to obtain the necessary adjustment.

Tighten
Tighten the nuts to 26 N·m (19 lb ft).

5. Close the rear compartment.
6. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
7. Repeat the adjustment procedure as necessary.
8. Remove the protective covering.
9. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .