Circuit Description
The keyless entry antenna - back up is located in the glove compartment area and is used as a short range low frequency (LF) transmitter. When a valid key fob is within the passenger compartment and the brake pedal is depressed and the ignition button is pressed the keyless entry antenna transmitter broadcasts a challenge within the passenger compartment to the key fob. If the response from the key fob via radio frequency (RF) is a valid response and all the security requirement are met the vehicles engine will start or be able to go into accessory mode.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B3122 Keyless Entry Antenna 4 Performance
Conditions for Setting the DTC
The remote control door lock receiver (RCDLR) will set this DTC during antenna activation if the keyless entry antenna - back up is open, or has a high resistance. The RCDLR can only set a DTC when it is the vehicle system voltage is between 9-16 volts.
Action Taken When the DTC Sets
The RCDLR will set and store a DTC B3122.
Conditions for Clearing the DTC
| • | The RCDLR no longer detects an open or a high resistance on the antenna circuit. |
| • | The use of a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that DTC B3122 is a current DTC.
-
This step tests for power and ground to the keyless entry antenna.
Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Keyless Entry Schematics Connector End View Reference: Keyless Entry Connector End Views | |||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
|
Important: To achieve service by pass mode, key ON engine OFF, a programmed key fob must be detected within the passenger compartment of the vehicle.
Does the scan tool display DTC B3122 as a current DTC? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | |||||||
|
Important:
Important: Use a DMM to record the voltage pulse using the MIN MAX setting to capture the AC voltage pulse to the passive antenna. Important: The ignition start button must be pressed to produce the voltage pulse to the passive antenna.
Was an A/C voltage signal greater than 1.2 V captured on the DMM? | Go to Step 6 | Go to Step 4 | |||||||
4 | Test both the keyless entry antenna power and ground circuit for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 5 | ||||||
5 | Inspect for poor connections at the RCDLR. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 7 | ||||||
6 | Inspect for poor connections at the keyless entry antenna - back up. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 9 | ||||||
7 | Test the keyless entry antenna power circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 8 | ||||||
8 | Replace the RCDLR. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 11 | -- | ||||||
9 | Test both the keyless entry antenna power and ground circuit for a short to power. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 10 | ||||||
10 | Replace the keyless entry antenna - back up. Refer to Ignition Lock Key Transmitter Antenna Replacement - Instrument Panel . Did you complete the replacement? | Go to Step 11 | -- | ||||||
11 |
Does the DTC reset? | Go to Step 3 | System OK | ||||||
