GM Service Manual Online
For 1990-2009 cars only

Circuit Description

A normal function of the transmission control module (TCM) is to perform an internal test that verifies the security of the diagnostic and shift calibration programming. The programming must contain security codes that enable a software lock to engage. The software lock is designed to prevent unauthorized changes to the diagnostics or shift calibrations. The software lock utility is processed independently from the diagnostic and shift calibration software and contains application specific data. This software lock data is entered into the TCM during the final assembly of the vehicle.

When the security codes from the diagnostic and shift calibration software fail to engage the software lock, the TCM sets DTC P0602. DTC P0602 is a type A DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0602 Transmission Control Module (TCM) Not Programmed

Conditions for Running The DTC

The ignition is ON.

Conditions for Setting The DTC

The TCM detects an unlocked calibration memory range.

Action Taken When the DTC Sets

    • The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the first trip when the Conditions for Setting the DTC are met.
    • The TCM turns off power to all solenoids.
    • The transmission will operate in fifth gear if the vehicle has successfully completed a 1-2 upshift in the current ignition cycle. If the vehicle has not completed a 1-2 upshift in the current ignition cycle, the transmission will operate in fourth gear.
    • The TCM commands maximum line pressure.
    • The TCM freezes transmission adaptive functions.
    • Powertrain braking is disabled.
    • The TCC is disabled.
    • At the time of the first failure, the TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as a Failure Record.
    • At the time of the second failure, the ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as a Freeze Frame.
    • The TCM stores DTC P0602 in TCM history.

Conditions for Clearing the MIL/DTC

    • The ECM turns OFF the MIL after the sixth consecutive drive trip in which the TCM does not send a MIL illumination request.
    • A scan tool can clear the MIL/DTC.
    • The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring.
    • The TCM cancels the default actions when the ignition is OFF long enough in order to power down the TCM.

Diagnostic Aids

DTC P0602 may set as a result of TCM reprogramming.

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step eliminates the TCM software as a possible cause of the DTC. If the DTC continues to set after reprogramming, the fault is in the TCM hardware.

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.
  3. Important: 

       • Before clearing the DTC, use the scan tool in order to record the ECM Freeze Frame and the TCM Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the ECM and the TCM.
       • Using the Clear Info function erases stored DTCs in both the ECM and TCM.

  4. Record the DTC Failure Records.
  5. Clear the DTC.
  6. Turn OFF the ignition for at least 30 seconds.
  7. Turn ON the ignition.

Did DTC P0602 reset?

--

Go to Step 3

Go to Diagnostic Aids

3

Perform the Transmission Control Module Reprogramming Procedure.

Refer to Control Module References in Computer/Integrated Systems for replacement, set-up and programming.

Is the action complete?

--

Go to Step 5

Go to Step 4

4

Replace the TCM.

Refer to Control Module References in Computer/Integrated Systems for replacement, set-up and programming.

Is the action complete?

--

Go to Step 5

--

5

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Turn OFF the ignition for at least 30 seconds.
  4. Turn ON the ignition.
  5. Select Specific DTC.
  6. Enter DTC P0602.

Has the test run and passed?

--

Go to Step 6

Go to Step 2

6

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK