Diagnostic Instructions

DTC Descriptors

DTC P1516: Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance

DTC P2101: Throttle Actuator Position Performance

DTC P2119: Throttle Closed Position Performance

DTC P2176: Minimum Throttle Position Not Learned

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Motor Control 1	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176
Motor Control 2	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176	P1516, P2101, P2119, P2176

Circuit/System Description

The engine control module (ECM) is the control center for the throttle actuator control (TAC) system. The ECM determines the drivers intent and then calculates the appropriate throttle response. The ECM achieves throttle positioning by providing a pulse width modulated voltage to the TAC motor. The TAC system uses the following circuits:

Two processors are also used to monitor the TAC system data. Both processors are located within the ECM. Both processors monitor each other's data to verify that the indicated throttle position is correct.

Conditions for Running the DTC

P1516 and P2101

P2119

P2176

Conditions for Setting the DTC

P1516

The indicated throttle position does not match the predicted throttle position for less than 1 second.

P2101

The indicated throttle position does not match the predicted throttle position for less than 1 second.

P2119

The ECM determines that the throttle blade did not return to the rest position within 1 second.

P2176

The difference between the predicted and the actual throttle position is more than a calibrated amount for more than 1.8 seconds.

Action Taken When the DTC Sets

Conditions for Clearing the MIL/DTC

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Circuit/System Verification

1. Ignition ON, engine OFF, observe the throttle position (TP) sensor 1 and TP sensor 2 indicated position with a scan tool. The indicated position parameter should increase as the pedal is applied and decrease as the pedal is released. When no accelerator pedal activity is detected, the throttle position will return to the spring loaded default position.
2. Engine running, observe the DTC information with a scan tool. DTCs P1516, P2101, P2119, or P2176 should not set.
3. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Important: A low voltage condition may set this DTC.

1. Review the Freeze Frame/Failure Records and ensure sufficient ignition voltage was present when the DTC was set.

⇒	If voltage was low, verify with the owner that the battery was not discharged.

Caution: Turn OFF the ignition before inserting fingers into the throttle bore. Unexpected movement of the throttle blade could cause personal injury.

2. Inspect the throttle body for the following conditions:

•	A throttle blade that is NOT in the rest position

•	A throttle blade that is binding when opening or closing

•	A throttle blade that is free to move in the open or closed positions WITHOUT spring pressure

⇒	If a condition is found, replace the throttle body.

Important: Disconnecting the throttle body harness connector causes additional DTCs to set.

3. Ignition OFF, disconnect the harness connector at the throttle body.
4. Ignition ON, verify that a test lamp does not illuminate between motor control circuit 1 terminal 4, and ground.

⇒	If the test lamp illuminates, test the motor control circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Ignition ON, verify that a test lamp does not illuminate between motor control circuit 2 terminal 6, and ground.

⇒	If the test lamp illuminates, test the motor control circuit for a short to voltage. If the circuit tests normal, replace the ECM.

6. Ignition ON, verify that a test lamp does not illuminate between motor control circuit 1 terminal 4 and B+.

⇒	If the test lamp illuminates, test the motor control circuit for a short to ground. If the circuit tests normal, replace the ECM.

7. Ignition ON, verify that a test lamp does not illuminate between motor control circuit 2 terminal 6 and B+.

⇒	If the test lamp illuminates test the motor control circuit for a short to ground. If the circuit tests normal, replace the ECM.

8. Ignition OFF, allow sufficient time for the ECM to completely power down. Connect a DMM between the motor control 1 terminal 4 and ground.

Important: When measuring peak voltage, ensure that the DMM is on the proper voltage scale and that the response time is set to 1 ms.

9. Measure for B+ on the motor control 1 circuit terminal 4 as the ignition is turned ON.

⇒	If the peak voltage is not within 1 volt of B+, test the circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

10. Ignition OFF, allow sufficient time for the ECM to completely power down.
11. Measure for B+ on the motor control 2 circuit terminal 6 as the ignition is turned ON.

⇒	If the peak voltage is not within 1 volt of B+, test the circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

12. If all circuits test normal, replace the throttle body.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.