Circuit Description
The memory seat and telescoping steering column position settings are stored in the left hand seat control module (SCM). The SCM measures and stores the steering column position by using a position sensor, which is an internal part of the telescoping actuator. The SCM provides the position sensor with a 5-volt reference and ground. The SCM monitors the position sensor signal voltage, which ranges from 0.1-4.78 volts depending on the steering column position. The steering column position sensor becomes active only when the SCM detects a steering column switch input.
DTC Descriptor
This diagnostic supports the following DTC:
DTC B2860 Telescope Position Sensor
Conditions for Setting the DTC
The steering column position sensor signal, to the SCM, is less than 0.1 volt or greater than 4.78 volts for 2 seconds or more.
Action Taken When the DTC Sets
| • | A history DTC B2860 is stored in the SCM memory. |
| • | This DTC can only be set as a history code even if the malfunction is current. |
| • | No driver warning message will be displayed for this DTC. |
| • | The memory operation/function of the faulted position sensor is disabled. |
Conditions for Clearing the DTC
| • | The steering column position sensor input, to the SCM, is within 0.1-4.78 volts for 2 seconds or more. |
| • | A scan tool can clear this DTC. |
Diagnostic Aids
| • | If the DTC does not reset after the code is cleared the problem may be intermittent. Perform the tests shown while moving related wiring and connectors. This can often cause the malfunction to occur. Refer to Testing for Intermittent Conditions and Poor Connections. |
| • | The following conditions may also cause an intermittent malfunction: |
| - | There is an intermittent open, short to ground, or short to voltage in steering column telescope motor signal circuit. |
| - | The steering column position sensor is open or shorted internally. |
| • | If the SCM is unable to determine the correct steering column position, limited manual operation of the telescoping steering column will be functional, but the SCM will be unable to recall the correct memory settings. |
| • | Using a scan tool, select SCM data display and monitor the Column Position Feedback data. Operate the steering column in both directions while monitoring the position sensor data. The voltage should range from 0.1-4.78 volts depending on the steering column position. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for the proper operation of the circuit in the high voltage range.
-
This step tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
-
This step tests for a short to ground in the 5-volt reference circuit.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Tilt/Telescoping Steering Column Schematics Connector End View Reference: Steering Wheel and Column Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the Column Position Feedback data parameter is within the specified range? | 0.1-4.78 V | Go to Diagnostic Aids | Go to Step 3 |
Does the scan tool indicate that the Column Position Feedback data parameter is greater than the specified value? | 4.78 V | Go to Step 4 | Go to Step 8 | |
Does the scan tool indicate that the Column Position Feedback data parameter is less than the specified value? | 0.1 V | Go to Step 5 | Go to Step 9 | |
Does the scan tool indicate that the Column Position Feedback data parameter is greater than the specified value? | 4.78 V | Go to Step 7 | Go to Step 6 | |
6 | Test the 5-volt reference circuit of the telescoping sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 12 |
7 | Test the 5-volt reference circuit of the telescoping sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 11 |
8 | Test the signal circuit of the telescoping sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 12 |
9 | Test the signal circuit of the telescoping sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 10 |
10 | Test the low reference circuit of the telescoping sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 12 |
11 | Inspect for poor connections at the harness connector of the telescoping sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 13 |
12 | Inspect for poor connections at the harness connector of the seat control module (SCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 14 |
13 | Replace the telescoping sensor. Refer to Telescope Actuator Assembly Replacement . Did you complete the replacement? | -- | Go to Step 15 | -- |
14 | Replace and calibrate the SCM. Refer to Memory Seat Control Module Replacement and Telescoping Steering Column Calibration . Did you complete the replacement and the calibration? | -- | Go to Step 15 | -- |
15 |
Does DTC B2860 reset? | -- | Go to Step 2 | System OK |
