Transmission Fluid Cooler Hose/Pipe Connector Replacement Lower Radiator

Important: The transmission oil cooler in held into position inside the radiator by the TOC fittings.

Service one TOC fitting at a time. Removal of both TOC fittings will cause the cooler tank to fall out of position and require radiator removal to install the TOC fittings.
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Position a drain pan under the vehicle.
3. Disengage the plastic cap from the TOC fitting.

Pull the plastic cap back along the pipe.

4. Disconnect the TOC line from the TOC fitting. Refer to LINK .



5. Remove the TOC fitting from the radiator.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the TOC fitting to the radiator.

Tighten
Tighten the fitting to 18 N·m (13 lb ft).

2. Connect the TOC line to the TOC fitting. Refer to LINK .

Important: Ensure the cooler line being installed has a plastic cap on the end that connects to the quick connect fitting. If no plastic cap exists, or the plastic cap is damaged, obtain a new cap. Install the cap on to the cooler line prior to cooler line installation.

Do not manually depress the retaining clip when installing the plastic cap.
3. Snap the plastic cap onto the TOC fitting.
4. Ensure that the plastic cap is fully seated against the fitting.



5. Ensure that no gap is present between the cap and the fitting.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Inspect the fluid level and add fluid if necessary. Refer to Transmission Fluid Check .

Transmission Fluid Cooler Hose/Pipe Connector Replacement Upper Radiator

1. Remove the radiator support. Refer to Radiator Support Replacement .

Important: The transmission oil cooler in held into position inside the radiator by the TOC fittings.

Service one TOC fitting at a time. Removal of both TOC fittings will cause the cooler tank to fall out of position and require radiator removal to install the TOC fittings.
2. Disengage the plastic cap from the TOC fitting.

Pull the plastic cap back along the pipe.

3. Disconnect the TOC line from the TOC fitting. Refer to LINK .



4. Remove the TOC fitting from the radiator.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the TOC fitting to the radiator.

Tighten
Tighten the fitting to 18 N·m (13 lb ft).

2. Connect the TOC line to the TOC fitting. Refer to LINK .

Important: Ensure the cooler line being installed has a plastic cap on the end that connects to the quick connect fitting. If no plastic cap exists, or the plastic cap is damaged, obtain a new cap. Install the cap on to the cooler line prior to cooler line installation.

Do not manually depress the retaining clip when installing the plastic cap.
3. Snap the plastic cap onto the TOC fitting.
4. Ensure that the plastic cap is fully seated against the fitting.



5. Ensure that no gap is present between the cap and the fitting.
6. Install the radiator support. Refer to Radiator Support Replacement .
7. Inspect the fluid level and add fluid if necessary. Refer to Transmission Fluid Check .