GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 XLR 🢒 Roof 🢒 Folding Top 🢒 Folding Top Quarter Inner Frame Support Bracket Replacement

Removal Procedure

    Caution: Refer to Eye Protection Caution in the Preface section.

    Caution: Refer to Folding Top Hydraulic Pressure Caution in the Preface section.

    Caution: Refer to Servicing Electrical Components Caution in the Preface section.


    Object Number: 1294372 Size: SH
  1. Place the folding top in the up position.
  2. Open the rear compartment.
  3. Disconnect the battery. Refer to Battery Negative Cable Disconnection and Connection .

    4. Object Number: 1274144 Size: SH
  4. Lower the rear compartment partition (1).
  5. Place a protective covering over the rear compartment interior and the adjacent body panels.
  6. Remove the side compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side or to Rear Compartment Side Trim Replacement - Right Side .
  7. Locate the hydraulic pump beneath the carpet in the storage compartment on the driver side of the rear compartment.

    8. Object Number: 1274131 Size: SH
  8. Turn the hydraulic pump bypass valve (1) counterclockwise until the valve stops.

    9. Object Number: 1250804 Size: SH
  9. When replacing the left side, perform the following steps. Skip these steps for the right side:
    10. 9.1. Remove the bolts (1) from the hydraulic pump bracket.
    9.2. Set the pump on the storage compartment floor.

    Object Number: 1251425 Size: SH
  10. Remove the spring-clip (1) from the upper compartment lid hydraulic cylinder retainer pin.
  11. Remove the upper cylinder retainer pin (2).

    12. Object Number: 1273751 Size: SH
  12. Remove the spring-clip (1) from the lower compartment lid hydraulic cylinder retainer.
  13. Remove the lower cylinder retainer pin (2).
  14. Leaving the hydraulic hoses attached, remove the cylinder from the original position. Set the cylinder aside in a safe place.
  15. Remove the compartment lid strut actuator. Refer to Folding Top Compartment Lid Strut Actuator Replacement - Rear .

    16. Object Number: 1526393 Size: SH
  16. Using a light colored grease pencil, mark the sound deadener mat on the wheelhouse along the inboard edge of the quarter inner longitudinal support frame. This mark will be used to verify that the frame has not shifted when the support is removed.

    17. Important: Mark the location of any shims found between the quarter inner frame support bracket and the longitudinal support frame and/or floor.


    Object Number: 1524379 Size: SH
  17. Remove the bolts (1) and nuts (2) securing the quarter inner frame support bracket to the longitudinal support frame.

    18. Object Number: 1526399 Size: SH
  18. Place the shims (1), as required, between the bottom surface of the longitudinal support frame and the wheelhouse mat. The shims should support the frame at the current elevation, but not lift the frame off the wheelhouse.

    19. Object Number: 1524380 Size: SH
  19. Pull the carpet up and over the retaining stud. Peel back enough carpet to access the area.
  20. Remove the nuts that secure the quarter inner frame support bracket to the weld studs coming up through the floor.
  21. Remove the wheelhouse liner panel in order to access the 2nd weld stud head for drilling. Refer to Rear Wheelhouse Panel Liner Replacement .
  22. From the underside of the vehicle, drill out the center of the weld studs enough to break the heads loose from the floor.
  23. Remove the remaining studs.
  24. Lower the vehicle.
  25. Remove the quarter inner frame support bracket by sliding the bracket free toward the center of the vehicle.

Installation Procedure
  1. Install any previously removed floor shims to the marked area(s).
  2. Position the quarter inner frame support bracket to the vehicle by sliding the bracket from center outward.
  3. Install any previously removed shims into position between the frame support bracket and the longitudinal support frame.

    4. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1524379 Size: SH

    Important: Reverse the bolt on the vertical surface of the frame support bracket so the nut is on the inside. This will allow access with a torque wrench.

  4. Ensure that the longitudinal support frame is still aligned to the grease pencil mark on the sound deadener. Install the bolts attaching the frame support bracket to the longitudinal support frame.

    5. Tighten
    Tighten the bolts to 37 N·m (27 lb ft)

  5. From the underside of the vehicle, insert an M8 flange head bolt or Hex with flat washer through the bracket where the studs were previously drilled out.
  6. From the rear compartment, install the original nut/washer (2) onto the 2 bolts (1).

    7. Tighten
    Tighten the nuts to 37 N·m (27 lb ft)


    Object Number: 1250804 Size: SH
  7. When replacing the left side, perform the following steps. Skip these steps for the right side:
    8. 7.1. Position the hydraulic pump to the mounting location.
    7.2. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.
    7.3. Install the bolts (1) to the hydraulic pump bracket.

    Tighten
    Tighten the bolts to 18 N·m (13 lb ft).

  8. Install the compartment lid strut actuator. Refer to Folding Top Compartment Lid Strut Actuator Replacement - Rear .

    9. Object Number: 1273751 Size: SH
  9. Install the compartment lid hydraulic cylinder to the link.
  10. Install the lower cylinder retainer pin (2).
  11. Install the lower cylinder retainer spring-clip (1).

    12. Object Number: 1251425 Size: SH
  12. Install the upper cylinder retainer pin (2).
  13. Install the spring-clip to the upper cylinder retainer pin.
  14. Remove the positioning shims between the longitudinal support frame and the wheelhouse mat.
  15. Install the side compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side or to Rear Compartment Side Trim Replacement - Right Side .
  16. Remove the protective covering from the rear compartment.

    17. Object Number: 1274131 Size: SH
  17. Turn the pump bypass valve (1) clockwise until the valve stops.

    18. Object Number: 1274144 Size: SH
  18. Raise the rear compartment partition (1).
  19. Connect the battery. Refer to Battery Negative Cable Disconnection and Connection .
  20. Inspect the hydraulic system for fluid leaks.
  21. Inspect the hydraulic system fluid level and add fluid as needed. Refer to Folding Top Fluid Addition .
  22. Close the rear compartment.
  23. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .
  24. Raise the vehicle.
  25. Rustproof the bolt heads and the surrounding metal on the undercarriage.
  26. Install the wheelhouse liner panel. Refer to Rear Wheelhouse Panel Liner Replacement .