• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
Hazard Switch Signal | 2 | 2 | 2 | -- |
Left Turn Signal Switch Signal | 1 | 1 | -- | -- |
Right Turn Signal Switch Signal | 1 | 1 | -- | -- |
Left Front Turn Signal Lamp Control | B3948 02 | B3948 05 | B3948 05 | -- |
Right Front Turn Signal Lamp Control | B3949 02 | B3949 05 | B3949 05 | -- |
Left Rear Turn Lamp Control | B3950 02 | B3950 05 | B3950 05 | -- |
Right Rear Turn Lamp Control | B3951 02 | B3951 05 | B3951 05 | -- |
Hazard Switch Ground | -- | 2 | 2 | -- |
Left Rear Stop/Turn Lamp Ground | -- | 1 | 1 | -- |
Right Rear Stop/Turn Lamp Ground | -- | 1 | 1 | -- |
Turn Signal/Multifunction Switch Ground | -- | 1 | 1 | -- |
Turn Signal Lamp - LF Ground | -- | 1 | 1 | -- |
Turn Signal Lamp - RF Ground | -- | 1 | 1 | -- |
1. Turn Signal Lamps and/or Indicators Malfunction 2. Hazard Lamps Malfunction |
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to the front and rear turn signal lamps through there respective voltage supply circuits. Ground for the left rear turn signal lamp is supplied at G301. Ground for the right rear turn signal lamp is supplied at G302.
Battery voltage must be between 9-16 volts.
This DTC will set when the BCM detects a short to ground in the LR turn signal voltage supply circuit.
This DTC will set when the BCM detects an open or short to voltage in the LR turn signal voltage supply circuit.
This DTC will set when the BCM detects a short to ground in the RR turn signal voltage supply circuit.
This DTC will set when the BCM detects an open or short to voltage in the RR turn signal voltage supply circuit.
• | When DTC B3950 02 is present, the LR turn signal lamp will not operate. |
• | When DTC B3950 05 is present, the LR turn signal lamp will be ON at all times for a short to voltage condition. For an open condition, the LR turn signal lamp will be inoperative. |
• | When DTC B3951 02 is present, the RR turn signal lamp will not operate. |
• | When DTC B3951 05 is present, the RR turn signal lamp will be ON at all times for a short to voltage condition. For an open condition, the RR turn signal lamp will be inoperative. |
• | The condition responsible for setting the DTC no longer exists. |
• | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
• | Check the LR turn signal bulb. If the bulb is open, DTC B3950 05 will set as current only. |
• | Check the RR turn signal bulb. If the bulb is open, DTC B3951 05 will set as current only. |
Exterior Lighting Systems Description and Operation
Control Module References for scan tool information
⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• | Control Module References for BCM replacement, setup, and programming |