GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0463: Fuel Level Sensor 1 Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Fuel Level Sensor 1 Signal

P0462

1

P0463

P0464

P0463

P0461

Fuel Level Sensor 2 Signal

P2067

1

P2068

P2068

P2066 or P2636

Fuel Level Sensor Low Reference

--

1

P0463

P2068

P0464

P0463

P2068

P0461

P2066 or P2636

1. Fuel Gage Inaccurate or Inoperative

Circuit/System Description

The primary fuel level sender and the secondary fuel level sender changes resistance based on fuel level. The engine control module (ECM) monitors the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to determine the fuel level. When the fuel tank is full, the resistances of both fuel level senders are low and the ECM senses a low signal voltage on both the signal circuits of the primary fuel level sender and the secondary fuel level sender. When the fuel tanks are empty, the resistances of the fuel level senders are high and the ECM senses a high signal voltage. The ECM uses the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via serial data circuit to the instrument cluster in order to control the fuel gage.

Conditions for Running the DTC

    • The ignition is ON.
    • The system voltage is between 11-18 volts.

Conditions for Setting the DTC

    • The primary fuel level sensor voltage is greater than 3.5 volts.
    • The above condition is present for greater than 24 seconds.

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The driver information center (DIC) displays the FUEL LEVEL LOW message.
    • The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.

Reference Information

Schematic Reference

Instrument Cluster Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Instrument Cluster Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information.

Circuit/System Verification

Ignition ON, observe the scan tool Fuel Level Sensor Left Tank parameter. The reading should be between 0.9 V-3.0 V.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the primary fuel level sensor.
  2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal 4 and ground.
  3. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  4. Ignition ON, install a 3A fused jumper wire between the signal circuit terminal 1 and the low reference circuit terminal 4. Verify the scan tool Fuel Level Sensor Left Tank parameter is less than 0.45 volt.
  5. If greater than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
  6. If all circuits test normal, perform the fuel level sensor component test before replacing the primary fuel level sensor.

Component Testing

  1. Ignition OFF, remove the primary fuel level sensor.
  2. While sweeping the primary fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms between signal terminal 1 and the low reference terminal 4.
  3. If not within the specified range, replace the primary fuel level sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Level Sensor Replacement - Left Side for the 4.6L engine
    •  Fuel Level Sensor Replacement - Left Side for the 4.4L engine
    •  Control Module References for the ECM replacement, setup, and programming