Special Tools
J 28467-B
Universal Engine Support Fixture
Removal Procedure
- Recover the refrigerant from the A/C system. Refer to
Refrigerant Recovery and Recharging
.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove the wheelhouse panel. Refer to
Front Wheelhouse Liner Replacement
.
- Disconnect the lower transmission oil cooler (TOC) line from the radiator. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Remove the lower TOC line from the radiator.
- Remove the A/C compressor. Refer to
Air Conditioning Compressor Replacement
.
- Disconnect the lower TOC line from the auxiliary TOC. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Remove the lower TOC line from the auxiliary TOC.
- Remove the accessory belt tensioner
top bolt (1).
- Remove the accessory belt tensioner lower bolt (2).
- Remove the accessory belt tensioner.
- Remove the A/C compressor and power steering pump bracket bolts.
- Remove the A/C compressor and power steering pump bracket.
- Raise the engine cradle back into position.
Important: It is not necessary to fully tighten the cradle nuts to specification at this time. They will be removed again at a later step. Tighten until the cradle mounting nuts contacts the engine cradle.
- Install the RH cradle mounting nuts.
- Remove the support jacks from beneath the vehicle.
- Lower the vehicle.
- Install the engine support fixture. Refer to
Engine Support Fixture
.
- Raise the vehicle approximately 0.61 mm (2.0 ft) off the ground.
- Support the engine cradle with a jack stands.
- Remove the RH cradle mounting nuts.
- Lower the RH engine cradle assembly approximately 51.0 mm (0.375 in)
- Remove the RH engine mount upper nut.
- Remove the RH engine mount lower nut
- Remove the RH engine mount bracket bolts.
Important: It is necessary to elevate the engine assembly slightly to allow clearance for the RH engine mount bracket removal.
- Using the
J 28467-B
, raise the engine assembly approximately 19.0 mm (0.75 in) to remove RH engine mount bracket
- Remove the RH engine mount bracket.
- Remove the RH engine mount heat shield from the engine mount.
- Remove the RH engine mount.
- Raise and support the vehicle.
- Remove the TOC line to oil pan retaining nuts.
- Remove the TOC line to oil pan retaining clips.
- Disconnect the upper and lower TOC retainer clip.
- Disconnect the front TOC lines from the rear TOC line set. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Disconnect the oil level sensor electrical connector.
Important: Note the position of the TOC lines to ensure proper installation.
- Remove the TOC lines.
Installation Procedure
- Install the TOC lines.
- Connect the oil level sensor electrical connector.
- Connect the front TOC lines to the rear TOC line set. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Connect the upper and lower TOC retainer clip.
- Install the TOC line to oil pan retaining clips.
Notice: Refer to Fastener Notice in the Preface section.
- Install the TOC line to oil pan retaining nuts.
Tighten
Tighten the nuts to 12 N·m (9 lb ft).
- Lower the vehicle.
Important: When installing the engine mount, be sure to have the locating dowel in the correct position.
- Install the RH engine mount.
- Install the RH engine mount heat shield to the engine mount.
- Install the RH engine mount bracket.
- Install the RH engine mount bracket bolts.
Tighten
Tighten the bolts to 58 N·m (43 lb ft).
- Using the
J 28467-B
, lower the engine assembly into position.
- Install the RH engine mount lower nut
Tighten
Tighten the nut to 58 N·m (43 lb ft).
- Install the RH engine mount upper nut.
Tighten
Tighten the nut to 58 N·m (43 lb ft).
- Install the A/C compressor and power steering pump bracket.
- Install the A/C compressor and power steering pump bracket bolts.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- Install the accessory belt tensioner.
- Install the accessory belt tensioner top bolt (1).
Important: Tighten in sequence.
Tighten
Tighten the bolt to 25 N·m (18 lb ft).
- Install the accessory belt tensioner lower bolt (2).
Tighten
Tighten the bolt to 25 N·m (18 lb ft).
- Install the A/C compressor. Refer to
Air Conditioning Compressor Replacement
.
- Install the lower TOC line to the auxiliary TOC.
- Connect the lower TOC line to the auxiliary TOC. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Install the lower TOC line to the radiator.
- Connect the lower TOC line to the radiator. Refer to
Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection
.
- Install the wheelhouse panel. Refer to
Front Wheelhouse Liner Replacement
.
- Lower the vehicle.
- Evacuate and recharge the A/C system. Refer to
Refrigerant Recovery and Recharging
.
- Check the transmission fluid level, add if necessary. Refer to
Transmission Fluid Fill Procedure
.