Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC C0186 00: Lateral Accelerometer CircuitDTC C0186 5A: Lateral Accelerometer Circuit Plausibility Failure
DTC C0196 00: Yaw Rate Circuit
DTC C0196 5A: Yaw Rate Circuit Plausibility Failure
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ignition Voltage | C0710 00, U2142 00 | C0710 00, U2142 00 | -- | C0710 5A, C0186 5A, C0196 5A |
Low Reference | C0710 00, U2142 00 | C0710 00, U2142 00 | C0710 00, U2142 00 | C0710 5A, C0186 5A, C0196 5A |
CAN Bus High Serial Data | C0710 00, U2100 00, U2142 00, C0196 00 | C0710 00, U2142 00 | C0710 00, U2142 00 | C0710 5A, C0186 5A, C0196 5A |
CAN Bus Low Serial Data | C0710 00, U2142 00 | C0710 00, U2142 00 | C0710 00, U2100 00, U2142 00 | C0710 5A, C0186 5A, C0196 5A |
Circuit/System Description
The yaw rate and the lateral accelerometer sensors are combined into one sensor, external to the electronic brake control module (EBCM). The vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The yaw rate/lat sensor communicates with the EBCM via discrete CAN Bus High and CAN Bus Low serial data circuits.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
| • | Short to ground on the CAN High serial data circuit. |
| • | The yaw/lateral combination sensor fails an internal self test. |
| • | Communication is lost between the EBCM and the yaw/lateral combination sensor. |
| • | The correlation error between the yaw/lateral combination sensor and steering angle sensor. |
Action Taken When the DTC Sets
One or more of the following actions may occur:
| • | The EBCM disables the antilock brake system (ABS)/traction control system (TCS) and vehicle stability enhancement system (VSES) for the duration of the ignition cycle. |
| • | A DIC message and/or a warning message may be displayed |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present. |
| • | The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Reference Information
Schematic Reference
Antilock Brake System Schematics
Connector End View Reference
Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Verify that DTC C0710, U2100, or U2142 and not set.
- Ignition OFF, disconnect the harness connector at the yaw rate/lat sensor.
- Ignition OFF for 60 seconds, test for less than 5 ohms between the low reference circuit terminal 1 and ground.
- Ignition ON, test for B+ between the ignition voltage circuit terminal 4 and ground.
- If all circuits test normal, replace the yaw rate/lat sensor.
| ⇒ | If C0710, U2100, or U2142 are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle. |
| ⇒ | If greater than the specified range, test the low reference circuit for an open/high resistance. |
| ⇒ | If not within the specified range, test the ignition voltage circuit for a short to ground or open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement
