GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2009 🢒 XLR 🢒 Roof 🢒 Folding Top 🢒 Folding Top Compartment Lid Link Replacement - Rear

Removal Procedure

    Object Number: 1294372 Size: SH
  1. Place the folding top in the up position.
  2. Open the rear compartment.

    3. Object Number: 1274144 Size: SH
  3. Lower the rear compartment partition (1).
  4. Place a protective covering over the interior and the adjacent body panels.
  5. Locate the hydraulic pump beneath the carpet in the storage compartment on the driver side of the trunk.

    6. Object Number: 1274131 Size: SH
  6. Turn the pump bypass valve (1) counterclockwise until the valve stops turning.
  7. Remove the side compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side or Rear Compartment Side Trim Replacement - Right Side.

    8. Object Number: 1251422 Size: SH
  8. Using a grease pencil, mark the location of the P-clips to the hydraulic cylinder hoses and electrical wires.
  9. Remove the closeout panel position switch. Refer to Folding Top Stowage Compartment Rear Panel Position Switch Replacement.
  10. Remove the rear storage compartment panel. Refer to Folding Top Stowage Compartment Rear Panel Replacement.
  11. Remove the rear compartment lid. Refer to Folding Top Stowage Compartment Lid Replacement.
  12. Remove the P-clip screws (1) that attach the hoses and the wires to the link.

    13. Object Number: 1251424 Size: SH
  13. Remove the link conduit screws (1).
  14. Remove the link conduit (2).
  15. Remove the hydraulic cylinder from the storage compartment closeout panel. Do NOT disconnect the hoses. Refer to Folding Top Storage Compartment Panel Hydraulic Cylinder Replacement - Rear.

    16. Object Number: 1251425 Size: SH
  16. Remove the spring-clip (1) from the hydraulic cylinder retainer pin.
  17. Remove the retainer pin (2).

    18. Object Number: 1251426 Size: SH
  18. While pushing up on the link, remove the travel limit screw (1) from the link.
  19. Support the link to prevent the link from swinging down when you remove the strut actuator.

    20. Object Number: 1251427 Size: SH
  20. Use a flat-bladed tool to lift up on the retainer clip (2) on the link side of the strut actuator.

    21. Caution: Apply pressure only at the end of the strut actuator that you are removing or attaching. DO NOT apply pressure to the middle of the rod because damage or bending will result.

  21. Remove the strut actuator (2) from the ball joint (1) on the link.

    22. Object Number: 1251428 Size: SH
  22. Remove the front link bolts (1).

    23. Object Number: 1251429 Size: SH
  23. Remove the rear link shoulder bolt (1).
  24. Remove the link from the vehicle.

Installation Procedure

    Object Number: 1247429 Size: SH
  1. Position the link to the vehicle. Verify that the switch pin (2) is positioned between the bracket (3) and the link (1).

    2. Object Number: 1251429 Size: SH
  2. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.

    3. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the rear link shoulder bolt (1) and tighten to 36 N·m (27 lb ft).

    4. Object Number: 1251428 Size: SH
  4. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.
  5. Install the front link bolts (1) and tighten to 8 N·m (71 lb in).

    6. Object Number: 1251427 Size: SH

    Caution: Apply pressure only at the end of the strut actuator that you are removing or attaching. DO NOT apply pressure to the middle of the rod because damage or bending will result.

  6. Lift the link to the full upright position and install the strut actuator  (2) to the ball joint (1) on the link.

    7. Object Number: 1251426 Size: SH
  7. While pushing up on the link, install the travel limit screw (1) to the link and tighten to 3 N·m (27 lb in).

    8. Object Number: 1251425 Size: SH
  8. Install the retainer pin (2) to the hydraulic cylinder.
  9. Install the spring clip (1) to the hydraulic cylinder retainer pin.
  10. Install the hydraulic cylinder to the closeout panel in the rear storage compartment. Refer to Folding Top Storage Compartment Panel Hydraulic Cylinder Replacement - Rear.

    11. Object Number: 1251424 Size: SH
  11. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.
  12. Position the link conduit (2) to the link. Install the link conduit screws (1) and tighten to 6 N·m (53 lb in).
  13. Align the P-clips to the grease marks on the hydraulic cylinder hoses and the electrical wires.

    14. Object Number: 1251422 Size: SH
  14. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.
  15. Install the P-clip screws (1) that attach the hoses and the wires to the link and tighten to 6 N·m (53 lb in).
  16. Install the rear compartment lid. Refer to Folding Top Stowage Compartment Lid Replacement.
  17. Install the rear storage compartment panel. Refer to Folding Top Stowage Compartment Rear Panel Replacement.
  18. Install the position switch to the storage compartment closeout panel. Refer to Folding Top Stowage Compartment Rear Panel Position Switch Replacement.
  19. Install the side compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side or Rear Compartment Side Trim Replacement - Right Side.

    20. Object Number: 1274131 Size: SH
  20. Turn the pump bypass valve (1) clockwise until the valve stops.
  21. Remove the protective covering.
  22. Install the support and the carpet over the hydraulic pump.

    23. Object Number: 1274144 Size: SH
  23. Raise the rear compartment partition (1).
  24. Close the rear compartment.
  25. Cycle the folding top under power through one complete cycle in both directions.
  26. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation.