GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2009 🢒 XLR 🢒 Preface 🢒 Dangers, Warnings, and Cautions 🢒 Battery Positive and Negative Cable Replacement

Battery Positive and Negative Cable Replacement LC3

Removal Procedure
  1. Disconnect the battery negative cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.

    2. Object Number: 1709697 Size: SH
  2. Loosen the battery positive cable nut (1) and disconnect the battery positive cable (2) from the battery (3).
  3. Open the stud cover on the fuse/relay center.
  4. Remove the battery positive cable nut and disconnect the battery positive cable lead from the fuse/relay center stud.
  5. Remove the battery cable clips.
  6. Remove the battery negative cable to frame rail nut and disconnect the battery negative cable from the frame rail stud.

    7. Object Number: 932138 Size: SH
  7. Remove the battery cable bolt (3) securing the battery negative cable (1) and engine harness ground pack (2) to the right rear cylinder head.
  8. Remove the supercharger. Refer to Supercharger Replacement.

    9. Object Number: 1333671 Size: SH
  9. Disconnect the starter jumper wiring harness (2) from the engine harness connector (1).

    10. Object Number: 1237944 Size: SH
  10. Remove the positive battery cable terminal nut and disconnect the terminals (2) from the starter solenoid.

    11. Object Number: 1237973 Size: SH
  11. Disconnect the battery positive/starter cable from the generator:
    12. 11.1. Slide the boot (1) back along the cable.
    11.2. Remove the battery positive/starter cable nut (2).
    11.3. Remove the battery positive/starter cable terminal (3) from the stud (4).

    Object Number: 1333715 Size: SH
  12. Remove the positive battery cable routing clip bolt (1) securing the cable and clip to the front of the engine.
  13. Remove the battery positive and negative cable assembly.

Installation Procedure
  1. Install the battery positive and negative cable assembly.

    2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1237973 Size: SH
  2. Connect the battery positive/starter/generator cable to the generator.
    3. 2.1. Install the cable terminal (3) on the generator stud (4). The wire should be between the 2  and 4 o'clock position.
    2.2. Install the terminal nut (2) and tighten to 20 N·m (15 lb ft).
    2.3. Slide the boot (1) back into place over the stud (4) and the nut (2).

    Object Number: 1333715 Size: SH
  3. Install the positive battery cable routing clip bolt (1) into the cable retaining clip and attach to the front of the engine. Tighten the bolt to 35 N·m (26 lb ft).

    4. Object Number: 1237944 Size: SH

    Note: Ensure the engine harness leads are positioned on the solenoid prior to the positive cable terminal being installed.

  4. Install the battery positive cable terminals and nut to the starter solenoid and tighten.
    5. • Tighten the large nut (2) to 12 N·m (106 lb in).
    • Tighten the small nut to 4 N·m (35 lb in).

    Object Number: 1333671 Size: SH
  5. Connect the starter jumper wiring harness (2) to the engine harness connector (1).
  6. Install the supercharger. Refer to Supercharger Replacement.

    7. Object Number: 932138 Size: SH
  7. Position the battery negative cable (1) and engine harness ground pack (2) to the right rear cylinder head and install the battery cable bolt (3). Tighten the battery negative cable routing clip bolt to 35 N·m (26 lb ft).
  8. Position the battery negative cable to frame rail stud and install the negative battery cable to frame rail nut and tighten to 11 N·m (97 lb in).
  9. Install the battery clips.
  10. Position the positive battery cable lead to the fuse/relay center stud and install the positive battery cable nut and tighten to 12 N·m (106 lb in).
  11. Close the stud cover on the fuse/relay center.

    12. Object Number: 1709697 Size: SH
  12. Connect the positive battery cable (2) to the battery (3) and tighten the nut (1) to 8 N·m (71 lb in).
  13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive and Negative Cable Replacement LH2

Removal Procedure
  1. Disconnect the battery negative cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.

    2. Object Number: 1709697 Size: SH
  2. Loosen the battery positive cable nut (1) and disconnect the battery positive cable (2) from the battery (3).
  3. Open the stud cover on the fuse/relay center.
  4. Remove the battery positive cable nut and disconnect the battery positive cable lead from the fuse/relay center stud.
  5. Remove the battery cable clips.
  6. Remove the battery negative cable to frame rail nut and disconnect the battery negative cable from the frame rail stud.

    7. Object Number: 932138 Size: SH
  7. Remove the battery cable bolt (3) securing the battery negative cable (1) and engine harness ground pack (2) to the right rear cylinder head.
  8. Remove the intake manifold. Refer to Intake Manifold Replacement.

    9. Object Number: 1333671 Size: SH
  9. Disconnect the starter jumper wiring harness (2) from the engine harness connector (1).

    10. Object Number: 1237944 Size: SH
  10. Remove the positive battery cable terminal nut and disconnect the terminals (2) from the starter solenoid.

    11. Object Number: 1237973 Size: SH
  11. Disconnect the battery positive/starter cable from the generator:
    12. 11.1. Slide the boot (1) back along the cable.
    11.2. Remove the battery positive/starter cable nut (2).
    11.3. Remove the battery positive/starter cable terminal (3) from the stud (4).

    Object Number: 1333715 Size: SH
  12. Remove the positive battery cable routing clip bolt (1) securing the cable and clip to the front of the engine.
  13. Remove the battery positive and negative cable assembly.

Installation Procedure
  1. Install the battery positive and negative cable assembly.

    2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1237973 Size: SH
  2. Connect the battery positive/starter/generator cable to the generator.
    3. 2.1. Install the cable terminal (3) on the generator stud (4). The wire should be between the 2  and 4 o'clock position.
    2.2. Install the terminal nut (2) and tighten to 20 N·m (15 lb ft).
    2.3. Slide the boot (1) back into place over the stud (4) and the nut (2).

    Object Number: 1333715 Size: SH
  3. Install the positive battery cable routing clip bolt (1) into the cable retaining clip and attach to the front of the engine and tighten to 35 N·m (26 lb ft).

    4. Object Number: 1237944 Size: SH

    Note: Ensure the engine harness leads (2) are positioned on the solenoid prior to the positive cable terminal being installed.

  4. Install the battery positive cable terminals and nut to the starter solenoid and tighten.
    5. • Tighten the large nut (2) to 12 N·m (106 lb in).
    • Tighten the small nut to 4 N·m (35 lb in).

    Object Number: 1333671 Size: SH
  5. Connect the starter jumper wiring harness (2) to the engine harness connector (1).
  6. Install the intake manifold. Refer to Intake Manifold Replacement.

    7. Object Number: 932138 Size: SH
  7. Position the battery negative cable (1) and engine harness ground pack (2) to the right rear cylinder head and install the battery cable bolt (3).

    8. Tighten
    Tighten the battery positive cable routing clip bolt to 35 N·m (26 lb ft).

  8. Position the battery negative cable to frame rail stud and install the negative battery cable to frame rail nut and tighten to 11 N·m (97 lb in).
  9. Install the battery clips.
  10. Position the positive battery cable lead to the fuse/relay center stud and install the positive battery cable nut and tighten to 12 N·m (106 lb in).
  11. Close the stud cover on the fuse/relay center.

    12. Object Number: 1709697 Size: SH
  12. Connect the positive battery cable (2) to the battery (3) and tighten the nut (1) to 8 N·m (71 lb in).
  13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.