| Table 1: | WSS Temperature vs. Sensor Resistance (2WD only) |
| Table 2: | WSS Temperature vs. Sensor Resistance (AWD only) |
Circuit Description
The wheel speed sensor coil emits an electromagnetic field. A toothed ring on the wheel passes by the wheel speed sensor and disrupts this electromagnetic field. The disruption in the field causes the wheel speed sensor to produce a sinusoidal (AC) voltage signal. The frequency and amplitude of the sinusoidal (AC) voltage signal are proportional to the speed of the wheel. The amplitude of the wheel speed signal is also directly related to the distance between the wheel speed sensor coil and the toothed ring. This distance is referred to as the air gap.
Conditions for Setting the DTC
| • | No output signal from the left front wheel speed sensor for 1.0 second |
| • | Excessive left front wheel speed sensor resistance for 1.0 second |
Action Taken When the DTC Sets
| • | The ABS indicator lamp turns on |
| • | The ABS disables |
DTC C0225 is a Condition Latched DTC, which indicates that the above actions remain true only as long as the condition persists.
DTC C0225 is a DRP Non Critical malfunction. If any other DTC sets before this DTC is investigated and cleared, this will become a DRP Critical malfunction and the BRAKE indicator lamp will also turn on.
Conditions for Clearing the DTC
| • | Repair the conditions responsible for setting the DTC |
| • | Use the Scan Tool Clear DTCs function. |
| • | A Condition Latched DTC may exist momentarily, or constantly. In either case, the DTC will be stored in the EBCM memory until it is repaired, and/or the DTC is cleared. After the DTC is repaired and/or cleared and the ignition is turned to ON, the ABS lamp will remain lit until the EBCM completes its power-up self test. This test concludes when the vehicle has reached a speed of greater than 13 km/h (8 mph) and the wheel speed inputs have been checked by the EBCM. |
Diagnostic Aids
Any of the following conditions may cause an intermittent malfunction:
| • | A poor connection |
| • | Wire insulation that is rubbed through |
| • | A wire breaks inside the insulation |
Thoroughly check any circuitry that is suspected of causing the intermittent complaint for the following conditions:
| • | Backed out terminals |
| • | Improper mating |
| • | Broken locks |
| • | Improperly formed or damaged terminals |
| • | Poor terminal to wiring connections |
| • | Physical damage to the wiring harness |
If the customer says that the ABS indicator lamp is on only during humid conditions such as rain, snow, or vehicle wash, then thoroughly inspect all wheel speed sensor circuits for signs of water intrusion. Use the following procedure:
- Spray the suspected area with a 5% salt water solution (two teaspoons of salt to 12 oz. of water)
- Drive the vehicle above 24 km/h (15 mph) for at least 30 seconds
If the DTC returns, replace the suspected harness.
When inspecting a wheel speed sensor, inspect the sensor terminals and the harness connector for corrosion. If evidence of corrosion exists, then replace the wheel speed sensor. Refer to Wheel Speed Sensor Replacement , or Wheel Speed Sensor Replacement .
Resistance of the wheel speed sensor will increase with an increase in sensor temperature. Refer to the following tables for temperature/resistance values.
°C | °F | Ohms |
|---|---|---|
Temperature vs Resistance Values (Approximate) | ||
-40 to 4 | -40 to 40 | 3915 to 5820 |
5 to 43 | 41 to 110 | 4760 to 6800 |
44 to 93 | 111 to 200 | 5560 to 8040 |
94 to 150 | 201 to 302 | 6600 to 9416 |
°C | °F | Ohms |
|---|---|---|
Temperature vs Resistance Values (Approximate) | ||
-40 to 4 | -40 to 40 | 702 to 1060 |
5 to 43 | 41 to 110 | 855 to 1230 |
44 to 93 | 111 to 200 | 1000 to 1440 |
94 to 150 | 201 to 302 | 1170 to 1661 |
Test Description
The numbers below refer to the steps in the diagnostic table:
-
This step checks the resistance of the left front wheel speed sensor circuit.
-
This step checks for continuity in the left front wheel speed sensor harness.
-
This step checks the resistance of the left front wheel speed sensor.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | Go to Step 2 | |
Is the resistance measurement within the specified range? | -- | Go to Step 5 | Go to Step 3 | |
Is the resistance measurement within the specified range? | 0-2 ohms | Go to Step 4 | Go to Step 10 | |
Using a J 39200 , measure the resistance between terminals A and B of the left front wheel speed sensor connector. (Refer to the tables on the facing page for applicable sensor resistance values. The values in these tables are for the temperature of the sensor, not the air temperature.) Is the resistance measurement within the specified range? | -- | Go to Step 7 | Go to Step 11 | |
5 | Inspect the 4-way EBCM harness connector for poor terminal contact or corrosion. Does damage or corrosion exist? | -- | Go to Step 8 | Go to Step 6 |
6 |
Does DTC C0225 set as a current DTC? | -- | Go to Step 9 | Go to Step 7 |
7 |
Is the repair complete? | -- | -- | |
8 | Make necessary repairs to the 4-way EBCM harness connector. Refer to Connector Repairs . Is the repair complete? | -- | -- | |
9 | Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Is the repair complete? | -- | -- | |
10 | Repair the open or high resistance in CKT 830 or CKT 873. Is the repair complete? | -- | -- | |
11 | Replace the wheel speed sensor. Refer to Wheel Speed Sensor Replacement . Is the repair complete? | -- | -- |
