GM Service Manual Online
For 1990-2009 cars only

Object Number: 600272  Size: SF
Engine Controls Components
Fuel Mixture Input Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The intake air temperature (IAT) sensor is a thermistor. The control module supplies the IAT sensor a reference voltage on the IAT sensor signal circuit and a ground circuit. When the IAT sensor resistance is high, indicating a cold sensor, the IAT sensor signal voltage remains near the supplied voltage and decreases the signal voltage as the sensor warms. The control module monitors the IAT sensor signal circuit in order to calculate the temperature of the air entering the engine.

This DTC is designed to detect intermittent low voltage signals on the IAT sensor signal circuit.

Conditions for Running the DTC

    • No active vehicle speed sensor (VSS) DTCs
    • The vehicle speed is more than 3 km/h (2 mph).
    • The engine has been running for more than 100 seconds.

Conditions for Setting the DTC

The vehicle control module (VCM) detects an intermittent low IAT voltage while the engine is running and vehicle exceeds 3 km/h (2 mph).

Action Taken When the DTC Sets

    • The control module stores the DTC in history after the first failure but will not illuminate the malfunction indicator lamp (MIL).
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores the failure information in the scan tools Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC

    • A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles.
    • A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant temperature exceeds 70°C (160°F) during the same ignition cycle.
    • Use the scan tool Clear Information function.

Diagnostic Aids

The IAT sensor measures the temperature of the ambient air entering the throttle body. The IAT temperature should be nearly the same as the temperature of the outside air. The intake air temperature should rise gradually as the engine warms up and the underhood temperature increases. An intermittent short to ground in the IAT sensor signal circuit could result in a DTC P1112. Also, a sensor may become skewed or mis-scaled. The Temperature vs. Resistance table will help to detect a skewed sensor.

Inspect for intermittents.

An intermittent may be caused by any of the following conditions:

    • A poor connection
    • Rubbed through wire insulation
    • A broken wire inside the insulation

Thoroughly inspect any circuitry that is suspected of causing the intermittent complaint. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. If the IAT sensor circuit voltage is more than 0.25 volts, the condition is present. Even though DTC P0112 did not set, this DTC is more comprehensive and may aid in diagnosis.

Step

Action

Values

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Important: Be sure to use the same diagnostic test equipment for all measurements.

  1. Install the scan tool.
  2. Turn ON the ignition, leaving the engine OFF.
  3. Display the IAT sensor voltage.

Is the voltage more than the specified value?

0.25 V

Go to DTC P0112 Intake Air Temperature (IAT) Sensor Circuit Low Voltage

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the IAT sensor harness connector.
  3. Inspect the IAT sensor harness connector and the terminals.

Did you find a problem?

--

Go to Step 6

Go to Step 4

4

  1. Disconnect the VCM C2 connector and the C3 connector.
  2. Inspect the terminals and the connectors.

Did you find a problem?

--

Go to Step 6

Go to Step 5

5

  1. Reconnect the VCM connectors and IAT sensor connector.
  2. Turn ON the ignition, leaving the engine OFF.
  3. Check for an intermittent short to ground in the IAT sensor signal circuit while moving the harness in various locations.
  4. Display the IAT sensor voltage while moving the harness.

Does the voltage fluctuate?

--

Go to Step 6

Go to Diagnostic Aids

6

Repair the circuit as necessary. Refer to Wiring Repairs or to Connector Repairs in Wiring Systems.

Is the action complete?

--

Go to Step 7

--

7

  1. Using the scan tool, clear the DTCs.
  2. Start the engine.
  3. Allow the engine to idle until the engine reaches a normal operating temperature.
  4. Select the DTC and the Specific DTC functions.
  5. Enter the DTC number that was set.
  6. Operate the vehicle within the Conditions for Setting the DTC until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

--

Go to Step 8

Go to Step 2

8

Does the scan tool display any additional undiagnosed DTCs?

--

Go to the applicable DTC table

System OK