Circuit Description
The crankshaft position (CKP) sensor is a sensor designed to detect changes in a magnetic field. The control module supplies the CKP sensor a signal and ground circuits. Ignition voltage is supplied to the sensor by an independent circuit. The CKP sensor produces a magnetic field whenever the ignition is ON. The CKP sensor is mounted near a reluctor wheel that is attached to the crankshaft. When the crankshaft rotates, when the engine is cranking or running, the toothed reluctor wheel changes the magnetic field. The CKP sensor converts each change in the magnetic field into a PULSE. The number of teeth on the reluctor wheel determines how many pulses the CKP sensor detects per crankshaft rotation. The CKP sensor signal is used in order to determine the engine speed, the crankshaft position, and to detect misfire.
If the vehicle control module (VCM) does not detect a CKP signal during engine cranking for a predetermined amount of time, this DTC will be set.
Conditions for Running the DTC
| • | The engine is cranking |
| • | Four or more camshaft position signals are detected |
Conditions for Setting the DTC
The CKP sensor signal is not detected for more than 0.5 second.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles. |
| • | The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records. |
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Inspect for intermittent conditions.
An intermittent may be caused by any of the following conditions:
| • | A poor connection |
| • | Rubbed through wire insulation |
| • | A broken wire inside the insulation |
Thoroughly inspect any circuitry that is suspected of causing the intermittent complaint. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step determines if the DTC P0336 is an intermittent.
-
This step checks the ignition positive voltage circuit to the CKP sensor.
-
This step checks the ground circuit of the CKP sensor .
-
This step checks the CKP sensor.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Does the vehicle start and continue to run? | -- | Go to Diagnostic Aids | ||
Does the test lamp illuminate? | -- | |||
Connect a test lamp between the ignition positive voltage to the CKP sensor harness connector and the sensor ground circuit. Does the test lamp illuminate? | -- | |||
Is the duty cycle within the specified range? | 40-60 % | |||
6 | Repair the open or the short in the ignition positive voltage circuit to the CKP sensor . Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
7 | Inspect the CKP sensor ground circuit for an open. Did you find a problem? | -- | ||
8 | Inspect for an open or a short in the CKP sensor signal circuit. Did you find a problem? | -- | ||
9 | Inspect the crankshaft position (CKP) sensor and the crankshaft reluctor wheel for damage. Refer to Diagnostic Aids. Did you find a problem? | -- | ||
10 |
Is the action complete? | -- | -- | |
11 | Inspect for a poor connection at the CKP sensor. Did you find a problem? | -- | ||
12 |
Important: Inspect the CKP sensor mounting surface to ensure the surface is clean and free of debris. Is the action complete? | -- | -- | |
13 | Inspect for a poor connection at the VCM. Did you find a problem? | -- | ||
14 | Repair the circuit as necessary. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
15 | Repair the circuit as necessary. Refer to Connector Repairs in Wiring Systems. Is the action complete? | -- | -- | |
16 |
Important: The replacement VCM must be programmed. Replace the VCM. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |
17 |
Does the scan tool indicate that this diagnostic Passed? | -- | ||
18 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the applicable DTC table | System OK |
