GM Service Manual Online
For 1990-2009 cars only

Object Number: 600572  Size: MF
Engine Controls Components
Emission Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The evaporative system includes the following components:

    • The fuel tank.
    • The evaporative emission (EVAP) vent solenoid.
    • The fuel tank pressure (FTP) sensor.
    • The fuel pipes and hoses.
    • The vapor lines.
    • The fuel cap.
    • The evaporative emission canister.
    • The purge lines.
    • The EVAP purge solenoid.

The EVAP purge solenoid valve allows the manifold vacuum to purge the canister. The vehicle control module (VCM) supplies a ground in order to energize the solenoid valve (purge ON). The EVAP purge solenoid control by the VCM is pulse width modulated (PWM) or turned ON and OFF several times a second. The duty cycle (pulse width) is determined by the engine operating conditions including the load, the throttle position, the coolant temperature, and the ambient temperature. The duty cycle is calculated by the VCM, and the purge solenoid is commanded ON when certain conditions have been met.

The system checks for failures that may cause the EVAP system to purge continuously by commanding the EVAP vent solenoid ON and the EVAP purge solenoid OFF (EVAP vent solenoid CLOSED, EVAP purge PWM 0 percent). If the fuel tank vacuum level increases during this test, a continuous purge flow condition is indicated. Inspect for the following conditions:

    • A leaking EVAP purge solenoid.
    • A grounded EVAP purge solenoid driver circuit.

If any of these conditions are present, a DTC P1441 sets.

Conditions for Running the DTC

    • No active manifold absolute pressure (MAP) sensor DTCs.
    • No active throttle position (TP) sensor DTCs.
    • No active vehicle speed (VSS) sensor DTCs.
    • No active oxygen (O2) sensor DTCs.
    • No active engine coolant temperature (ECT) sensor DTCs.
    • No active intake air temperature (IAT) sensor DTCs.
    • DTC P0125 not active.
    • The fuel level is more than 12.5 percent but less than 88 percent.
    • The system voltage is more than 10 volts but less than 17 volts.
    • The ECT is between 4°C and 30°C (39°F-86°F).
    • The IAT is between 4°C and 30°C (39°F-86°F).
    • The cold start temperature difference (ECT minus IAT) is less than:
       - 1.5°C (35°F) when the IAT is more than the ECT.
       - OR
       - 8°C (46°F) when the ECT is more than the IAT.
    • The BARO is more than 72.5 kPa.
    • The vent solenoid is commanded open.
    • The fuel tank vacuum is less than 7 inch H2O.
    • The throttle position is less than 75 percent.
    • The vehicle speed is less than 65 MPH.

Conditions for Setting the DTC

The EVAP system develops a vacuum more than a calibrated value when purge is not commanded.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles.
    • The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records.

Conditions for Clearing the MIL or DTC

    • The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed.
    • A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle.
    • Use a scan tool in order to clear the DTCs.

Diagnostic Aids

Important: An accurate indication of fuel level is required for the VCM to properly Pass or Fail this DTC. Always diagnose fuel level sensor DTCs before performing this DTCs diagnostic table. Always check for fuel level sensor DTCs stored in history.

A damaged harness may cause this DTC to set. Inspect the wiring harness to the EVAP purge solenoid and the fuel tank pressure sensor for an intermittent open or short circuit

Refer to Evaporative Emission System Cleaning before starting repairs.

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

The numbers below refer to the step numbers on the diagnostic table:

  1. Determines if the EVAP purge solenoid is leaking.

  2. Determines if the EVAP canister purge valve driver circuit is shorted to ground.

  3. Determines if the EVAP canister purge valve driver circuit wiring or the VCM are at fault.

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Disconnect the EVAP purge line from the EVAP purge solenoid.
  2. Connect a vacuum gauge (in Hg) to the solenoid purge port.
  3. Start the engine.
  4. After 30 seconds of engine run time, command the EVAP purge solenoid OFF with a scan tool.

Does the vacuum gauge indicate any vacuum while commanded OFF?

--

Go to Step 3

Refer to Diagnostic Aids

3

Disconnect the electrical connector from the purge solenoid.

Does the vacuum gauge still indicate vacuum?

--

Go to Step 4

Go to Step 5

4

Important:: Check for carbon contamination. Refer to Evaporative Emission System Cleaning .

Replace the EVAP purge solenoid.

Is the action complete?

--

Go to Step 8

--

5

  1. Turn OFF the ignition.
  2. Disconnect the VCM C3 connector.
  3. Connect a test lamp to B+, probe the EVAP purge solenoid driver circuit.
  4. Turn ON the ignition leaving the engine OFF.

Is the test lamp Illuminated?

--

Go to Step 7

Go to Step 6

6

Important: The replacement VCM must be programmed.

Replace the VCM. Refer to VCM Replacement/Programming .

Is the action complete?

--

Go to Step 8

--

7

Repair the short to ground in the EVAP Canister purge valve driver circuit.

Is the action complete?

--

Go to Step 8

--

8

  1. Using the scan tool, clear the DTCs.
  2. Start the engine.
  3. Select DTC and the Specific DTC function.
  4. Enter the DTC number which was set.
  5. Operate the vehicle, within the Conditions for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

--

Go to Step 9

--

9

Does the scan tool display any additional undiagnosed DTCs?

--

Go to applicable DTC table

System OK