GM Service Manual Online
For 1990-2009 cars only

Object Number: 572356  Size: SF
SIR Components
SIR Schematics
SIR Handling Caution
Handling ESD Sensitive Parts Notice

Circuit Description

The inflatable restraint sensing and diagnostic module (SDM) monitors the front end discriminating sensor circuit for front impact detection. The SDM processes the signal provided by the front end discriminating sensor to further support deployment of the air bags. The front end discriminating sensor is an input only to the SDM and does not directly cause air bag deployment. When you first turn the ignition switch to the RUN position, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. The SDM then performs the following continuous diagnostic tests on the deployment loops:

    • Deployment loop voltage out of range test
    • Deployment loop resistance measurement test

If the voltage out of range tests detects a short to voltage condition, the resistance measurement test for that deployment loop will not be performed.

Conditions for Setting the DTC

The SDM detects the voltage at the discriminating sensor signal input is 0.5 volts or less for 300 milliseconds.

Action Taken When the DTC Sets

    • The SDM disables the discriminating sensor input.
    • The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

Conditions for Clearing the DTC

    • The voltage at the discriminating sensor signal input is greater than 0.5 volts for 300 milliseconds.
    • You issue a scan tool CLEAR CODES command.
    • A history DTC will clear once 255 malfunction free ignition cycles have occurred.

When the SDM detects that no DTCs are present, the SDM commands the AIR BAG warning lamp OFF.

Diagnostic Aids

A broken or chafed wire in the inflatable restraint front end discriminating sensor circuit may cause an intermittent condition to occur. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table:

  1. Tests for a malfunctioning discriminating sensor.

  2. Tests for a short to ground in the discriminating sensor input circuit.

  3. Tests isolates a short to ground in the discriminating sensor input circuit to one side of the in-line harness connector.

Step

Action

Value(s)

Yes

No

1

Did you perform the SIR Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - SIR

2

  1. Turn OFF the ignition.
  2. Disconnect the inflatable restraint front end discriminating sensor. Refer to Inflatable Restraint Front End Discriminating Sensor Replacement .
  3. Using J 39200 DMM measure the resistance between the discriminating sensor terminals. Refer to Circuit Testing in Wiring Systems.

Does the resistance measure more than the specified value?

950 ohms

Go to Step 4

Go to Step 3

3

Replace the inflatable restraint front end discriminating sensor. Refer to Inflatable Restraint Front End Discriminating Sensor Replacement .

Did you complete the replacement?

--

Go to Step 8

--

4

  1. Disconnect the inflatable restraint sensing and diagnostic module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  2. Using J 39200 DMM measure the resistance from the discriminating sensor harness connector terminal A to ground. Refer to Circuit Testing in Wiring Systems.

Does the resistance measure less than the specified value?

OL

Go to Step 5

Go to Diagnostic System Check - SIR

5

  1. Turn OFF the ignition.
  2. Disconnect the discriminating sensor in-line harness connector. Refer to SIR Components .
  3. Using J 39200 DMM measure the resistance from the discriminating sensor in-line harness connector terminal A to ground. Refer to Circuit Testing in Wiring Systems.

Does the resistance measure less than the specified value?

OL

Go to Step 6

Go to Step 7

6

Locate and repair a short to ground in the discriminating sensor input circuit between the discriminating sensor in-line harness connector and the discriminating sensor harness connector. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 8

--

7

Locate and repair a short to ground in the discriminating sensor input circuit between the discriminating sensor in-line harness connector and the inflatable restraint sensing and diagnostic module (SDM) harness connector. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 8

--

8

  1. Reconnect all SIR system components.
  2. Verify that all components, connectors, and CPAs are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK