GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The throttle position (TP) sensor is used by the powertrain control module (PCM) in order to determine the throttle plate angle for various engine management systems. The TP sensor is a potentiometer type sensor with the following three circuits:

    • A 5-volt reference circuit
    • A low reference circuit
    • A signal circuit

The PCM provides the TP sensor with a 5-volt reference circuit and a low reference circuit. Rotation of the TP sensor rotor from the closed throttle position to the wide open throttle (WOT) position provides the PCM with a signal voltage from less than 1 volt to more than 4 volts through the TP sensor signal circuit. If the PCM detects an excessively low signal voltage, this DTC will set.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

    • The TP sensor signal voltage is less than 0.1 volt.
    • The above condition is present for more than 2 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

If this DTC is determined to be intermittent, refer to Intermittent Conditions .

Test Description

The number below refers to the step number on the diagnostic table.

  1. Any incorrectly operating components that share the 5-volt reference circuit with the TP sensor could cause a low voltage condition on this circuit.

DTC P0122 Throttle Position (TP) Sensor Circuit Low Voltage

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Connect a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to observe the TP sensor voltage parameter.

Is the voltage is less than the specified value?

0.1 V

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn the ignition OFF for 30 seconds.
  3. Operate the vehicle within the Conditions for Running the DTC, or as closely as possible to the Freeze Frame/Failure Records conditions.

Does the diagnostic test fail this ignition?

--

Go to Step 4

Go to Step 10

4

  1. Turn OFF the ignition.
  2. Disconnect the TP sensor harness connector.
  3. Connect a fused jumper between the 5-volt reference circuit and the signal circuit at the TP sensor harness connector.
  4. Turn ON the ignition, with the engine OFF.
  5. Use the scan tool in order to observe the TP sensor voltage parameter.

Does the voltage equal the specified value?

5 V

Go to Step 11

Go to Step 5

5

  1. Remove the fused jumper.
  2. Use a DMM in order to test for voltage between the 5-volt reference circuit of the TP sensor and the low reference circuit of the TP sensor.

Does the DMM indicate voltage near the specified value?

5 V

Go to Step 9

Go to Step 6

6

Use the DMM in order to test the 5-volt reference circuit for an open and for high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 7

7

Test all of the 5-volt reference circuits for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 8

8

  1. Connect the DMM between the 5-volt reference circuit and the low reference circuit of the TP sensor.
  2. Observe the voltage display on the DMM while disconnecting all of the sensors that use a 5-volt reference signal, one at a time.
  3. A change in the voltage indicates a faulty component.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 10

9

Use the DMM in order to test the TP sensor signal circuit for an open, for a high resistance, and for short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 10

10

Inspect for poor connections at the PCM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 13

11

Inspect for poor connections at the TP sensor harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

12

Replace the TP sensor. Refer to Throttle Position Sensor Replacement .

Did you complete the replacement?

--

Go to Step 14

--

13

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 14

--

14

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC.

Does the diagnostic test run and pass?

--

Go to Step 15

Go to Step 2

15

With a scan tool, observe the stored information, Capture info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK