Circuit Description
The Fuel Level sensor is an important input to the VCM for the Enhanced Evaporative System Diagnostic. The VCM needs the fuel level information in order to know the volume of fuel in the tank. The fuel level affects the rate of change in the air pressure in the EVAP system. Several of the Enhanced Evaporative System Diagnostic sub-test are dependent upon the correct fuel level information. The diagnostic will not run when the tank is greater than 85% or less than 15% full. (This sensor signal disables the misfire when the fuel levels are less than 15%).
Conditions for Running the DTC
The ignition switch is in the RUN position.
Conditions for Setting the DTC
The fuel level sensor voltage remains above 2.9 volts for more than 20 seconds.
Action Taken When the DTC Sets
The VCM will not turn ON the MIL.
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Check for the following conditions:
| • | A poor connection or damaged harness - Inspect VCM harness connectors for the following: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Poor wire to terminal connections |
| • | Intermittent test - monitor a scan tool or digital voltmeter connected between the related circuits while moving the connectors and harnesses. If the failure is induced, the voltage reading will change. This will help locate a circuit problem. |
| • | View the Fuel Level with a scan tool. Compare the scan tool value with the fuel gauge in the instrument cluster. If the scan tool value is approximately 99% and the instrument cluster's fuel gauge is indicating empty, then check for an open in the sensor ground between the VCM and the splice joining the shared components. |
Test Description
The numbers below refer to the step numbers in the diagnostic table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: : Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
2 |
Is the voltage greater than the specified value? | 2.9V | ||
3 | This DTC is intermittent. Are any other DTC stored? | -- | Go to applicable DTC table | Go to Diagnostic Aids |
Is the voltage near the specified value? | 5V | |||
5 | Check for a open in the Fuel Level signal circuit. Was a problem found? | -- | ||
6 | With a test light connected to B+, probe the Fuel Level ground circuit. Is the test light ON? | -- | ||
7 | Check for a short to voltage in the Fuel Level signal circuit. Was a problem found? | -- | ||
8 | Check for an open in the Fuel Level ground circuit. Was a problem found? | -- | ||
9 | Check the electrical connector at the Fuel Level Sender for corrosion and improper mating. Was a problem found? | -- | ||
10 | Repair the circuit as necessary. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
11 | Replace the Fuel Level Sender. Refer to Fuel Sender Assembly Replacement . Is action complete? | -- | ||
12 |
Is the action complete? | -- | -- | |
13 |
Does the scan tool indicate the diagnostic Passed? | -- | ||
14 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the Applicable DTC Table | System OK |
