Tools Required

J 21854-01 Pivot Pin Remover

1. Install the adapter and bearing assembly (2) onto the jacket assembly (1).
2. Install the EVO sensor assembly to the end of the steering shaft assembly.
3. Install the steering column seal (3) onto the adapter and bearing assembly (2).




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Important: If the steering column support assembly and the pivot pins have been staked 3 times they must be replaced.

4. Install the 4 TORX® screws (2) onto the steering column support assembly (1).

Tighten
Tighten the screws to 17 N·m(13 lb ft).




5. Install the centering sphere (1) and the joint preload spring (2) using the J 41688 . Lubricate the centering sphere (1) with lithium grease.



6. Compress the centering sphere and joint preload spring. Rotate the driver 90 degrees in the clockwise direction until the arms lock in place.



7. Install the race and upper shaft assembly. Rotate the race and upper shaft assembly 90 degrees and remove with the centering sphere.



8. Remove the race and upper shaft assembly with the J 41688 . Rotate the race and upper shaft assembly 90 degrees and remove.



9. Apply lithium grease to the race and upper shaft assembly (1) and then install the lower shaft assembly (2).



10. Install the steering shaft assembly (2) into the steering column tilt head assembly (1).



11. Install the tilt head assembly (1) and the lower steering shaft (3) into the steering column jacket assembly (2).




Important: If the steering column support assembly and the pivot pins have been staked 3 times they must be replaced.

12. Lubricate the pivot pins (1) with lithium grease.
13. Firmly seat each pivot pin (1) into the steering column tilt head assembly.
14. Stake the pivot pins (1).



15. Install the gearshift lever assembly support bracket.

Install the 3 flat head 6-lobed socket tapping screws.

Tighten
Tighten the screws to 10 N·m(89 lb in).




16. Install the cam bushing (2) from the cable shift cam assembly (1).
17. Install the cable shift cam assembly (1).
18. Install the hexagon flange head bolt.



19. Install the park lock cable assembly.
20. Install the 2 oval head 6-lobed socket tapping screws from the shift gate.

Tighten
Tighten the screws to 6.5 N·m(58 lb in).




21. Install the shift lever clevis (1).
22. Install the ball and actuator assembly (2).
23. Install the hexagon flanged head bolt.



24. Install the automatic transmission shift lock control actuator.
25. Install the gear shift lever and put the column in the neutral position.



26. Adjust the automatic transmission shift lock control actuator.

27.1.

Pull the tab (1) out on the block side (2) of the automatic transmission shift lock control actuator.

27.2.

Press on the adjuster block (2) to compress the internal adjuster spring to disengage the adjuster teeth. Slide the adjuster block as far away from the solenoid as possible.

27.3.

Lock in place by pushing the tab (1) back in.

27. Inspect the automatic transmission shift lock control actuator.

28.1.

The automatic transmission shift lock control actuator must lock the gear shift lever when it is put into the park position.

28.2.

When the column is installed in the vehicle you will not be able to shift the gear shift lever out of the park position without pressing on the brake pedal. The solenoid will be energized.

28.3.

Readjust if needed.

28. Install the lock module assembly. Refer to Electronic Column Lock Module - Assemble - Off Vehicle .
29. Install the tilt spring assembly. Refer to Tilt Spring - Assemble - Off Vehicle .
30. Install the turn signal and multifunction switch assembly. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .