SPECIAL POLICY - SAFETY BELT GUIDE COVER. Chevrolet Astro

NOTE: GM OF CANADA VERSION OF 98030 IS BELOW THE US VERSION ______________________________________________________________________

SPECIAL POLICIES 98030 JULY, 1998

SPECIAL POLICY

SUBJECT: 98030 - SPECIAL POLICY - SAFETY BELT GUIDE COVER

MODELS: 1996-1998 CHEVROLET AND GMC M/L PASSENGER VANS

********************************************************************** THIS SPECIAL POLICY IS IN EFFECT UNTIL JULY 31, 1999 **********************************************************************

CONDITION

SOME CUSTOMERS OF 1996-1998 M/L PASSENGER VANS MAY COMMENT ABOUT CONTACTING THE SAFETY BELT GUIDE COVER UPON EXITING THE VEHICLE.

CAUSE

THE TOP OF THE OLD DESIGNED SAFETY BELT GUIDE COVER PROJECTED ABOVE THE SEAT.

SPECIAL POLICY PRODUCT ENHANCEMENT

THIS SPECIAL POLICY COVERS THE CONDITION DESCRIBED ABOVE UNTIL JULY 31, 1999. DEALERS ARE TO INSTALL A REDESIGNED SAFETY BELT GUIDE COVER. USE THE FOLLOWING SERVICE PROCEDURE. THIS WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER DURING THIS TIME.

VEHICLES INVOLVED

INVOLVED ARE CERTAIN 1996-98 CHEVROLET AND GMC M/L PASSENGER VANS BUILT WITHIN THE FOLLOWING VIN BREAKPOINTS:

YEAR DIVISION MODEL PLANT CODE FROM THROUGH 1996 CHEVROLET M/L BALTIMORE "B" SOP EOP 1997 CHEVROLET M/L BALTIMORE "B" SOP EOP 1998 CHEVROLET M/L BALTIMORE "B" SOP WB142433 1996 GMC M/L BALTIMORE "B" SOP EOP 1997 GMC M/L BALTIMORE "B" SOP EOP 1998 GMC M/L BALTIMORE "B" SOP WB514678

PARTS INFORMATION

NOTE: KITS CONSISTS OF SAFETY BELT GUIDE COVERS FOR THE DRIVER'S AND PASSENGER'S SEAT.

PART NUMBER DESCRIPTION QUANTITY/ VEHICLE

88880017 GUIDE KIT (BLUE - 26I) 1 88880018 GUIDE KIT (NEUTRAL - 52I) 1 88880019 GUIDE KIT (RED - 79I) 1 88880020 GUIDE KIT (PEWTER - 92I) 1 88880021 GUIDE KIT (GRAY - 13I) 1

CUSTOMER NOTIFICATION

CUSTOMERS WILL BE NOTIFIED OF THIS SPECIAL POLICY ON THEIR VEHICLES BY GENERAL MOTORS (SEE COPY OF TYPICAL CUSTOMER LETTER INCLUDED WITH THIS BULLETIN - ACTUAL DIVISIONAL LETTER MAY VARY SLIGHTLY).

SERVICE PROCEDURE

INSPECTION PROCEDURE

IMPORTANT: ALL OF THE ILLUSTRATIONS SHOW THE RIGHT (PASSENGER) SEAT ASSEMBLY. THE GUIDE IS LOCATED ON THE OUTBOARD SIDE OF THE SEAT, NEXT TO THE DOOR (WHEN CLOSED). FOR EASE OF UNDERSTANDING, IT IS RECOMMENDED THAT THE PASSENGER SEAT/SHOULDER BELT OUTBOARD GUIDE BE REPLACED FIRST.

1. REVIEW THE ILLUSTRATIONS IN FIGURE 1 TO IDENTIFY THE ORIGINAL (OLD) DESIGN GUIDE FROM THE NEW DESIGN GUIDE.

2. DETERMINE WHETHER THE SEAT HAS A MANUAL OR POWER SEAT TRACK AND USE THE APPROPRIATE SERVICE PROCEDURE

REPLACEMENT PROCEDURE

REPLACEMENT OF SEAT/SHOULDER BELT GUIDE ON MANUAL SEATS (DRIVER OR PASSENGER)

1. MOVE THE MANUAL SEAT ASSEMBLY AS FAR REARWARD AS POSSIBLE.

IMPORTANT: REMOVAL OF THE GUIDE RETAINING BOLT IN THE NEXT STEP CAN BE ACCOMPLISHED EASILY IF DONE FROM BEHIND THE SEAT.

2. REMOVE THE BOLT THAT RETAINS THE SEAT/SHOULDER BELT GUIDE TO THE BOTTOM OF THE SEAT ASSEMBLY (FIGURE 2)

3. REMOVE THE SAFETY BELT GUIDE FROM UNDERNEATH THE SEAT ASSEMBLY.

4. TO REMOVE THE SAFETY BELT FROM THE GUIDE, INSERT A SMALL FLAT BLADED TOOL AS SHOWN IN FIGURE 5, TO RELEASE OR UNLOCK THE INNER GUIDE SECTION FROM THE OUTER GUIDE SECTION.

5. SLIDE THE INNER GUIDE SECTION IN THE DIRECTION SHOWN TO SEPARATE THE TWO PIECES.

6. REMOVE THE SAFETY BELT FROM THE GUIDE AND DISCARD BOTH GUIDE PIECES.

IMPORTANT: NEW GUIDES ARE MARKED "R" (RIGHT) FOR THE PASSENGER SEAT AND "L" (LEFT) FOR THE DRIVER'S SEAT.

7. POSITION THE NEW SAFETY BELT GUIDE UNDER THE SEAT ASSEMBLY.

8. INSTALL AND TIGHTEN THE RETAINING BOLT TO 30 NM (22 FT. LB.).

9. INSERT THE SAFETY BELT THROUGH THE OPENING IN THE GUIDE.

REPLACEMENT OF SEAT/SHOULDER BELT GUIDE ON POWER SEATS (DRIVER OR PASSENGER)

1. USING THE POWER SEAT SWITCH, RAISE OR TILT THE REAR PORTION OF THE SEAT AS HIGH AS POSSIBLE.

IMPORTANT: REMOVAL OF THE REAR TRIM COVER AND THE GUIDE RETAINING BOLT IN THE NEXT STEPS CAN BE ACCOMPLISHED EASILY IF DONE FROM BEHIND THE SEAT.

2. REMOVE THE TWO SCREWS THAT SECURE THE REAR TRIM COVER TO THE LOWER REAR OF THE POWER SEAT ASSEMBLY (FIGURE 3).

3. REMOVE THE BOLT THAT RETAINS THE SAFETY BELT GUIDE TO THE BOTTOM OF THE SEAT ASSEMBLY (FIGURE 4).

4. REMOVE THE SAFETY BELT GUIDE FROM UNDERNEATH THE SEAT ASSEMBLY.

5. TO REMOVE THE SAFETY BELT FROM THE GUIDE, INSERT A SMALL FLAT BLADED TOOL AS SHOWN IN FIGURE 5, TO RELEASE OR UNLOCK THE INNER GUIDE SECTION FROM THE OUTER GUIDE SECTION.

6. SLIDE THE INNER GUIDE SECTION IN THE DIRECTION SHOWN TO SEPARATE THE TWO PIECES.

7. REMOVE THE SAFETY BELT FROM THE GUIDE AND DISCARD BOTH GUIDE PIECES.

IMPORTANT: NEW GUIDES ARE MARKED "R" (RIGHT) FOR THE PASSENGER SEAT AND "L" (LEFT) FOR THE DRIVER'S SEAT.

8. POSITION THE NEW GUIDE UNDER THE SEAT ASSEMBLY.

9. INSTALL AND TIGHTEN THE RETAINING BOLT TO 30 NM (22 FT. LB.).

10. POSITION THE REAR TRIM COVER TO THE LOWER REAR OF THE POWER SEAT ASSEMBLY, INSTALL TWO SCREWS.

11. INSERT THE SAFETY BELT THROUGH THE OPENING IN THE GUIDE.

FIGURE 1 - PASSENGER SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND 1. ORIGINAL (OLD) DESIGN SAFETY/SHOULDER BELT GUIDE COVER

2. NEW DESIGN SAFETY/SHOULDER BELT GUIDE

FIGURE 2 - LOWER REAR OF MANUAL PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

FIGURE 3 - LOWER REAR OF POWER PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND 1. OUTBOARD SEAT TRACK 2. SAFETY/SHOULDER BELT GUIDE RETAINING BOLT

LEGEND 1. POWER SEAT ASSY REAR TRIM COVER 2. REAR TRIM COVER RETAINING SCREWS 3. OUTBOARD POWER SEAT TRACK

FIGURE 4 - LOWER REAR OF POWER PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. POWER SEAT ASSY WITH REAR TRIM COVER REMOVED

2. OUTBOARD POWER SEAT TRACK

3. SAFETY/SHOULDER BELT GUIDE RETAINING BOLT

FIGURE 5 - PASSENGER SIDE SAFETY BELT GUIDE SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. BACKSIDE OF ORIGINAL DESIGN SAFETY/SHOULDER BELT GUIDE COVER

2. LOCKING TABS

3. USE A SCREWDRIVER TO RELEASE LOCKING TAB

4. SLIDE INNER GUIDE OUT OF OUTER GUIDE IN DIRECTION SHOWN.

CLAIM INFORMATION

IMPORTANT: THIS SPECIAL POLICY IS IN EFFECT UNTIL JULY 31, 1999. DURING THE TIME THAT THIS SPECIAL POLICY IS IN EFFECT, THE FOLLOWING LABOR CODES AND TIMES SHOULD BE USED FOR CLAIM SUBMISSION.

REPAIR PART FAILED PARTS LABOR TYPE LABOR PERFORMED CNT P/N ALLOW CC-FC OP OF SEAT HRS

INSTALL SAFETY BELT GUIDE COVER 1 --- * MK-95 T5510

1 POWER AND 1 MANUAL SEAT 0.3 2 POWER SEATS 0.4 2 MANUAL SEATS 0.3

* THE "PARTS ALLOWANCE" SHOULD BE THE SUM TOTAL OF THE CURRENT GMSPO DEALER NET PRICE PLUS 40% FOR THE GUIDE KIT NEEDED TO COMPLETE THE REPAIR.

FIGURES: 7

Object Number: 484311 Size: MF

Object Number: 484313 Size: MF

Object Number: 484315 Size: SF

Object Number: 484317 Size: SF

Object Number: 484319 Size: SF

Object Number: 484321 Size: MF

Object Number: 484323 Size: MF

GM BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THESE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE TOOLS, EQUIPMENT, SAFETY INSTRUCTIONS, AND KNOW-HOW TO DO A JOB PROPERLY AND SAFEY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION. SEE YOUR DEALER/RETAILER FOR INFORMATION ON WHETHER YOUR VEHICLE MAY BENEFIT FROM THE INFORMATION.

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

DEAR CHEVROLET ASTRO VAN/GMC SAFARI CUSTOMER:

THIS LETTER IS TO INFORM YOU OF A SERVICE UPDATE AVAILABLE AT YOUR CHEVROLET/GMC DEALER IN THE EVENT YOU ARE DISSATISFIED WITH THE OPERATION OF THE FRONT SAFETY BELT GUIDE COVER. THIS UPDATE IS THE RESULT OF COMMENTS RECEIVED ABOUT CONTACTING THE SAFETY BELT GUIDE COVER WHEN EXITING THE VEHICLE.

A SERVICE KIT HAS BEEN DEVELOPED FOR THE INSTALLATION OF A REDESIGNED SAFETY BELT GUIDE COVER. THIS NEW SAFETY BELT GUIDE COVER SITS LOWER THAN THE ORIGINAL DESIGNED GUIDE COVER AND WILL MINIMIZE BODY CONTACT WITH THE GUIDE COVER WHEN EXITING THE VEHICLE. YOUR CHEVROLET/GMC DEALER HAS THE NECESSARY INSTRUCTIONS, AND THE REQUIRED PART KIT IS CURRENTLY AVAILABLE. IF YOU DESIRE THIS IMPROVEMENT BE MADE TO YOUR VEHICLE, PLEASE CONTACT YOUR CHEVROLET/GMC DEALER TO SCHEDULE AN APPOINTMENT. THIS IMPROVEMENT WILL BE AVAILABLE TO YOU AT NO CHARGE UNTIL JULY 31, 1999.

YOUR SATISFACTION WITH YOUR CHEVROLET ASTRO/GMC SAFARI VAN IS OF THE UTMOST IMPORTANCE TO US AND WE HAVE TAKEN THIS ACTION TO ENSURE THAT YOUR OWNERSHIP EXPERIENCE IS A PLEASURABLE ONE.

PAGE 7 JULY, 1998 BULLETIN NO.: 98030

********************************************************************** GM OF CANADA VERSION **********************************************************************

SPECIAL POLICY 98030 JULY 1998

SPECIAL POLICY

SUBJECT: 98030 - SPECIAL POLICY - SAFETY BELT GUIDE COVER

MODELS: 1996-1998 CHEVROLET AND GMC M/L PASSENGER VANS

********************************************************************** THIS SPECIAL POLICY IS IN EFFECT UNTIL JULY 31, 1999 **********************************************************************

CONDITION

SOME CUSTOMERS OF 1996-1998 M/L PASSENGER VANS MAY COMMENT ABOUT CONTACTING THE SAFETY BELT GUIDE COVER UPON EXITING THE VEHICLE.

CAUSE

THE TOP OF THE OLD DESIGNED SAFETY BELT GUIDE COVER PROJECTED ABOVE THE SEAT.

SPECIAL POLICY PRODUCT ENHANCEMENT

VEHICLES INVOLVED

INVOLVED ARE CERTAIN 1996-98 CHEVROLET AND GMC M/L PASSENGER VANS BUILT WITHIN THE FOLLOWING VIN BREAKPOINTS:

YEAR DIVISION MODEL PANT CODE FROM THROUGH 1996 CHEVROLET M/L BALTIMORE "B" SOP EOP 1997 CHEVROLET M/L BALTIMORE "B" SOP EOP 1998 CHEVROLET M/L BALTIMORE "B" SOP WB142433 1996 GMC M/L BALTIMORE "B" SOP EOP 1997 GMC M/L BALTIMORE "B" SOP EOP 1998 GMC M/L BALTIMORE "B" SOP WB514678

PARTS INFORMATION

PARTS REQUIRED TO COMPLETE THIS CAMPAIGN ARE TO BE OBTAINED FROM GENERAL MOTORS SERVICE PARTS OPERATIONS (GMSPO). PLEASE REFER TO YOUR "INVOLVED VEHICLES LISTING" PRIOR TO ORDERING REQUIREMENTS.

NOTE: KITS CONSISTS OF SAFETY BELT GUIDE COVERS FOR THE DRIVER'S AND PASSENGER'S SEAT.

PART NUMBER DESCRIPTION QUANTITY/VEHICLE

88880017 GUIDE KIT (BLUE-26I) 1 88880018 GUIDE KIT (NEUTRAL-52I) 1 88880019 GUIDE KIT (RED-79I) 1 88880020 GUIDE KIT (PEWTER-92I) 1 88880021 GUIDE KIT (GRAY-13I) 1

CUSTOMER NOTIFICATION

CUSTOMERS WILL BE NOTIFIED OF THE SPECIAL POLICY BY GENERAL MOTORS OF CANADA LIMITED (SEE COPY OF OWNER LETTER INCLUDED WITH THIS BULLETIN).

SERVICE PROCEDURE

INSPECTION PROCEDURE

IMPORTANT: ALL OF THE ILLUSTRATIONS SHOW THE RIGHT (PASSENGER) SEAT ASSEMBLY. THE GUIDE IS LOCATED ON THE OUTBOARD SIDE OF THE SEAT, NEXT TO THE DOOR (WHEN CLOSED). FOR EASE OF UNDERSTANDING, IT IS RECOMMENDED THAT THE PASSENGER SEAT/SHOULDER BELT OUTBOARD GUIDE BE REPLACED FIRST.

1. REVIEW THE ILLUSTRATIONS IN FIGURE 1 TO IDENTIFY THE ORIGINAL (OLD) DESIGN GUIDE FROM THE NEW DESIGN GUIDE.

2. DETERMINE WHETHER THE SEAT HAS A MANUAL OR POWER SEAT TRACK AND USE THE APPROPRIATE SERVICE PROCEDURE.

REPLACEMENT PROCEDURE

REPLACEMENT OF SEAT/SHOULDER BELT GUIDE ON MANUAL SEATS (DRIVER OR PASSENGER)

1. MOVE THE MANUAL SEAT ASSEMBLY AS FAR REARWARD AS POSSIBLE.

IMPORTANT: REMOVAL OF THE GUIDE RETAINING BOLT IN THE NEXT STEP CAN BE ACCOMPLISHED EASILY IF DONE FROM BEHIND THE SEAT.

2. REMOVE THE BOLT THAT RETAINS THE SEAT/SHOULDER BELT GUIDE TO THE BOTTOM OF THE SEAT ASSEMBLY (FIGURE 2).

3. REMOVE THE SAFETY BELT GUIDE FROM UNDERNEATH THE SEAT ASSEMBLY.

4. TO REMOVE THE SAFETY BELT FROM THE GUIDE, INSERT A SMALL FLAT BLADED TOOL AS SHOWN IN FIGURE 5, TO RELEASE OR UNLOCK THE INNER GUIDE SECTION FROM THE OUTER GUIDE SECTION.

5. SLIDE THE INNER GUIDE SECTION IN THE DIRECTION SHOWN TO SEPARATE THE TWO PIECES.

6. REMOVE THE SAFETY BELT FROM THE GUIDE AND DISCARD BOTH GUIDE PIECES.

IMPORTANT: NEW GUIDES ARE MARKED "R" (RIGHT) FOR THE PASSENGER SEAT AND "L" (LEFT) FOR THE DRIVER'S SEAT.

7. POSITION THE NEW SAFETY BELT GUIDE UNDER THE SEAT ASSEMBLY.

8. INSTALL AND TIGHTEN THE RETAINING BOLT TO 30 N M (22 FT. LB.).

9. INSERT THE SAFETY BELT THROUGH THE OPENING IN THE GUIDE.

REPLACEMENT OF SEAT/SHOULDER BELT GUIDE ON POWER SEATS (DRIVER OR PASSENGER)

1. USING THE POWER SEAT SWITCH, RAISE OR TILT THE REAR PORTION OF THE SEAT AS HIGH AS POSSIBLE.

IMPORTANT: REMOVAL OF THE REAR TRIM COVER AND THE GUIDE RETAINING BOLT IN THE NEXT STEPS CAN BE ACCOMPLISHED EASILY IF DONE FROM BEHIND THE SEAT.

2. REMOVE THE TWO SCREWS THAT SECURE THE REAR TRIM COVER TO THE LOWER REAR OF THE POWER SEAT ASSEMBLY (FIGURE 3).

3. REMOVE THE BOLT THAT RETAINS THE SAFETY BELT GUIDE TO THE BOTTOM OF THE SEAT ASSEMBLY (FIGURE 4).

4. REMOVE THE SAFETY BELT GUIDE FROM UNDERNEATH THE SEAT ASSEMBLY.

5. TO REMOVE THE SAFETY BELT FROM THE GUIDE, INSERT A SMALL FLAT BLADED TOOL AS SHOWN IN FIGURE 5, TO RELEASE OR UNLOCK THE INNER GUIDE SECTION FROM THE OUTER GUIDE SECTION.

6. SLIDE THE INNER GUIDE SECTION IN THE DIRECTION SHOWN TO SEPARATE THE TWO PIECES.

7. REMOVE THE SAFETY BELT FROM THE GUIDE AND DISCARD BOTH GUIDE PIECES.

IMPORTANT: NEW GUIDES ARE MARKED "R" (RIGHT) FOR THE PASSENGER SEAT AND "L" (LEFT) FOR THE DRIVER'S SEAT.

8. POSITION THE NEW GUIDE UNDER THE SEAT ASSEMBLY.

9. INSTALL AND TIGHTEN THE RETAINING BOLT TO 30 N M (22 FT. LB.).

10. POSITION THE REAR TRIM COVER TO THE LOWER REAR OF THE POWER SEAT ASSEMBLY, INSTALL TWO SCREWS.

11. INSERT THE SAFETY BELT THROUGH THE OPENING IN THE GUIDE.

FIGURE 1 - PASSENGER SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. ORIGINAL (OLD) DESIGN SAFETY/SHOULDER BELT GUIDE COVER

2. NEW DESIGN SAFETY/SHOULDER BELT GUIDE

FIGURE 2 - LOWER REAR OF MANUAL PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

FIGURE 3 - LOWER REAR OF POWER PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. OUTBOARD SEAT TRACK

2. SAFETY/SHOULDER BELT GUIDE RETAINING BOLT

LEGEND

1. POWER SEAT ASSEMBLY REAR TRIM COVER

2. REAR TRIM COVER RETAINING SCREWS

3. OUTBOARD POWER SEAT TRACK

FIGURE 4 - LOWER REAR OF POWER PASSENGER SIDE SEAT SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. POWER SEAT ASSEMBLY WITH REAR TRIM COVER REMOVED

2. OUTBOARD POWER SEAT TRACK

3. SAFETY/SHOULDER BELT GUIDE RETAINING BOLT

FIGURE 5 - PASSENGER SIDE SAFETY BELT GUIDE SHOWN (DRIVER'S SIDE OPPOSITE)

LEGEND

1. BACKSIDE OF ORIGINAL DESIGN SAFETY/SHOULDER BELT GUIDE COVER

2. LOCKING TABS

3. USE A SCREWDRIVER TO RELEASE LOCKING TAB

4. SLIDE INNER GUIDE OUT OF OUTER GUIDE IN DIRECTION SHOWN.

CLAIM INFORMATION

IMPORTANT: THIS SPECIAL POLICY IS IN EFFECT UNTIL JULY 31, 1999. DURING THE TIME THAT THIS SPECIAL POLICY IS IN EFFECT, THE FOLLOWING LABOUR CODES AND TIMES SHOULD BE USED FOR CLAIM SUBMISSION.

REPAIR PART FAILED PARTS LABOR TYPE LABOR PERFORMED CNT P/N ALLOW CC-FC OP OF SEAT HRS

INSTALL SAFETY BELT GUIDE COVER 1 --- * MK-95 T5510

1 POWER AND 1 MANUAL SEAT 0.3 2 POWER SEATS 0.4 2 MANUAL SEATS 0.3

* THE "PARTS ALLOWANCE" SHOULD BE THE SUM TOTAL OF THE CURRENT GMSPO DEALER NET PRICE PLUS 40% FOR THE GUIDE KIT NEEDED TO COMPLETE THE REPAIR.

GM BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THESE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE TOOLS, EQUIPMENT, SAFETY INSTRUCTIONS, AND KNOW-HOW TO DO A JOB PROPERLY AND SAFELY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION. SEE YOUR DEALER/RETAILER FOR INFORMATION ON WHETHER YOUR VEHICLE MAY BENEFIT FROM THE INFORMATION.

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION