Pitman Arm Replacement RWD

Tools Required

Important: Use the proper tool in order to separate all of the ball joints.

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



2. Remove the prevailing torque nut (2) from the connecting rod (1) ball stud at the pitman arm (3).

Discard the prevailing torque nut (2).




3. Use the J 24319-B in order to remove the connecting rod from the pitman arm.
4. Remove the prevailing torque nut and the washer from the steering gear shaft.

•	Discard the prevailing torque nut.

•	Mark the pitman arm and the pitman shaft in order to permit proper alignment during assembly.





Notice: Do not hammer on the pitman arm, pitman arm shaft or puller. Damage to the pitman arm or steering gear may result.

5. Use the J 29107-A in order to remove the pitman arm (1).
6. Inspect the ball stud threads for damage.
7. Inspect the ball stud seals for excessive wear.
8. Clean the threads on the ball stud and the ball stud nut.

1. Align the marks made on the pitman arm during removal in order to install the pitman arm on the pitman shaft.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the washer and the new prevailing torque nut to the pitman shaft.

Tighten
Tighten the pitman arm prevailing torque nut to 250 N·m (185 lb ft).




3. Use the J 29193 in order to install the connecting rod ball stud to the pitman arm.

Ensure that the seal is on the stud.

Tighten
Tighten the J 29193 to 54 N·m (40 lb ft) in order to seat the tapers.

4. Remove the J 29193 .



5. Install the new prevailing torque nut (2) to the connecting rod (1) ball stud at the pitman arm (3).

Tighten
Tighten the connecting rod to pitman arm prevailing torque nut to 62 N·m (48 lb ft).

6. Lower the vehicle.

Pitman Arm Replacement AWD

Tools Required

J 29107-A Pitman Arm Puller

Important: Use the proper tool in order to separate all of the ball joints.

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
3. Remove the power steering gear. Refer to Steering Gear Replacement in Power Steering System.



4. Remove the pitman arm retaining nut and washer.

Mark the pitman arm and the pitman shaft in order to permit proper alignment during assembly.





Notice: Do not hammer on the pitman arm, pitman arm shaft or puller. Damage to the pitman arm or steering gear may result.

5. Use the J 29107-A in order to remove the pitman arm.
6. Inspect the ball stud threads for damage.
7. Inspect the ball stud seals for excessive wear.
8. Clean the threads on the ball stud and the ball stud nut.

1. Align the marks made on the pitman arm during removal in order to install the pitman arm on the pitman shaft.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the washer and the pitman arm retaining nut.

Tighten
Tighten the pitman arm retaining nut to 250 N·m (185 lb ft).

3. Install the power steering gear. Refer to Steering Gear Replacement in Power Steering System.
4. Lower the vehicle.