GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 104280  Size: SH
  1. Block the drive wheels and place the vehicle in the neutral position.
  2. Remove the drivers side knee bolster. Refer to Driver Knee Bolster Replacement in Instrument Panel, Gages, and Console.
  3. Remove the bottom half of the steering column trim cover. Refer to Steering Column Trim Covers Replacement in Steering Wheel and Column.
  4. Remove the range selector cable end from the steering column shift controller ball stud .
  5. Remove the clip that secures the range selector cable to the steering column bracket.
  6. Remove the range selector cable from the steering column bracket.
  7. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  8. Object Number: 104277  Size: SH
  9. Remove the range selector cable end from the transmission range selector lever stud ball.
  10. Remove the clip from the bracket that secures the range selector cable to the transmission.
  11. Remove the range selector cable from the bracket.
  12. Remove the three range selector cable clips from the body.
  13. Remove the grommet from the hole in the floor panel.

  14. Object Number: 104279  Size: SH
  15. If the vehicle is equipped with a transfer case, remove the bolt and washer securing the clip and the range selector cable to the transfer case.
  16. Remove the range selector cable from the vehicle.

Installation Procedure


    Object Number: 104281  Size: SH
  1. Feed the steering column end of the range selector cable through the grommet hole in the floor panel.
  2. Lower the vehicle.

  3. Object Number: 104280  Size: SH
  4. Connect the range selector cable end to the steering column shift controller stud ball.
  5. Install the range selector cable to the steering column bracket.
  6. Install the clip that secures the range selector cable to the steering column bracket.

  7. Object Number: 104277  Size: SH
  8. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  9. Install the range selector cable to the transmission bracket.
  10. • Do not depress the adjustment locking tab located on the range selector cable.
    • Ensure that the tab remains positioned OUT.
    • Do not install the range selector cable end to the transmission shift lever stud ball at this time.

    Object Number: 642260  Size: SH
  11. Ensure that the transmission is in the mechanical neutral position.
  12. • Rotate the transmission range selector lever clockwise until it reaches the full clockwise stop position.
    • Move the range selector lever counterclockwise two detents.

    Object Number: 104282  Size: SH
  13. Position the range selector cable to assume a natural routing.
  14. The range selector cable must be free to move 20.0 mm (0.80 in) axially during the adjustment under adjustment spring loads.

  15. Pull the range selector cable end completely forward and release it. (When the cable is pulled completely forward and released, the adjustment spring will position the cable to its most rearward position.)
  16. Notice: Do not pull the shift lever ball stud forward of the transmission shift lever ball stud during installation. Pulling the shift cable end forward of the transmission shift lever ball stud before installing the shift cable end to the transmission shift lever ball stud will result in a poor adjustment.

  17. Connect the end of the range selector cable to the transmission range selector lever stud ball.
  18. Press the locking tab IN in order to retain the adjustment and to secure the cable to the transmission bracket.
  19. If the vehicle is equipped with a transfer case, install the bolt and washer securing clip and the cable to the transfer case.

  20. Object Number: 104281  Size: SH
  21. Install the grommet to the hole in the floor panel.
  22. Install the three range selector cable clips to the body.
  23. Lower the vehicle.
  24. Check for proper operation of the range selector cable.
  25. Install the lower half of the steering column trim cover. Refer to Steering Column Trim Covers Replacement in Steering Wheel and Column.
  26. Install the drivers side knee bolster. Refer to Driver Knee Bolster Replacement in Instrument Panel, Gages, and Console.
  27. Remove the wheel blocks.