Table 1: | BCM Scan Tool Data List |
Table 2: | IPC Scan Tool Data List |
Table 3: | PCM Scan Tool Data List |
The scan tool data lists contain all the instrument panel, gages, and console related parameters that are available on the scan tool. The parameters in the list are arranged in alphabetical order. The data list column indicates the location of the parameter within the scan tool menu selections.
Use the scan tool data lists as directed by a diagnostic table or in order to supplement the diagnostic procedures. Begin all of the diagnostic procedures with the Diagnostic System Check - Instrument Cluster , or Diagnostic System Check - Audible Warnings .
Use the scan tool data lists only after the following is determined:
• | There is no published DTC procedure nor published symptom procedure for the customer concern. |
• | The DTC or symptom procedure indicated by the diagnostic system check does not resolve the customer concern. |
The typical data values are obtained from a properly operating vehicle under the conditions specified in the first row of the scan tool data list table. Comparison of the parameter values from the suspect vehicle with the typical data values may reveal the source of the customer concern.
Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
---|---|---|---|
Operating Conditions: Ignition ON/Engine OFF/High Beams Off/Doors Closed/Trunk Closed/Park Brake Unapplied | |||
Battery Voltage | Data | Volts | Varies |
Chime | Outputs | On/Off | Off |
Driver Door Jamb Switch | Input 1 | Open/Closed | Closed |
Ignition 1 | Input 1 | Active/Inactive | Active |
Ignition 3 | Input 1 | Active/Inactive | Active |
Key in Ignition | Input 1 | Active/Inactive | Active |
Left Turn Signal | Inputs 2 | On/Off | Off |
Park Brake Switch | Inputs 1 | On/Off | Off |
Park Lamps | Input 2 | On/Off | Off |
Right Turn Signal | Inputs 2 | On/Off | Off |
Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
---|---|---|---|
Operating Conditions: Ignition ON/Engine OFF/Seat Belt Buckled/High Beams Off/Park Brake Unapplied | |||
ABS Lamp | Outputs | On/Off | Off |
Air Bag Lamp | Outputs | On/Off | Off |
Battery | Outputs | On/Off | On |
Battery Voltage | Data | Volts | Varies |
Brake Lamp | Outputs | On/Off | Off |
Dimming | Inputs | Active/Inactive | Inactive |
Displayed Odometer | Data | Kilometers (Miles) | Varies with the mileage of vehicle |
Displayed Trip Odometer | Data | Kilometers (Miles) | Varies with the mileage of vehicle |
Fasten Seat Belts | Outputs | On/Off | Off |
Hi Beam Lamp | Outputs | On/Off | Off |
Low Fuel Lamp | Outputs | On/Off | Off |
Module Part Number | Module Information | Numeric | Varies |
Monitored Coolant Temp | Data | Celsius (Fahrenheit) | 82-93°C (180-200°F) |
Monitored Fuel Level | Data | Percent | 0-100% |
Overspeed Lamp | Outputs | On/Off | Off |
Park Switch | Inputs | Open/Closed | Closed |
PRNDL State | Inputs | Park/ Reverse/ Neutral/ First/ Second/ Third/ Drive | Park |
Security Lamp | Outputs | On/Off/Flashing | Off |
Service AWD | Outputs | On/Off | Off |
Tow/Haul | Outputs | Engine Data 2 | Off |
Trip Reset Switch | Inputs | Active/Inactive | Inactive |
Vehicle Speed | Data | km/h (mph) | 0 km/h (0 mph) |
Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
---|---|---|---|
Operating Conditions: Engine Idling/Normal Operating Temperature | |||
ECT Sensor | Engine Data 1 Engine Data 2 Fuel Trim Data Enhanced EVAP Data Misfire Data | Celsius (Fahrenheit) | 85-105°C (185-220°F) |
Engine Oil Life Remaining | Engine Data 2 | Percent | 0-100% (Varies) |
Engine Oil Pressure Sensor | Engine Data 2 | Volts | 0-5 Volts (Varies) |
Engine Speed | Engine Data 1 Engine Data 2 Fuel Trim Data Misfire Data Enhanced EVAP | RPM | +- 100 RPM from desired idle speed |
Fuel Level Sensor | Engine Data 1 Enhanced EVAP Data | Voltage | 0-5 V |
MIL Command | Engine Data 2 | On/Off | Off |
Vehicle Speed Sensor | Engine Data 1 Engine Data 2 Fuel Trim Data Enhanced EVAP Data Misfire Data | Miles per hour (Kilometers per hour) | 0 mph (0 km/h) |