GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The Passlock™ system is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate or the ignition switch is operated while separated from the ignition lock cylinder case. The body control module (BCM) provides security system sensor power and low reference for the Passlock™ sensor. The BCM also measures the security system sensor voltage.

When the correct key is used to start the vehicle, a magnet on the lock cylinder passes close to the Passlock™ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock™ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle. The BCM will measure the voltage on the security sensor signal circuit and compare this voltage to a previously learned voltage. If the voltage measured is within the valid range, the BCM will send a class 2 message to the powertrain control module (PCM) to enable vehicle starting. If the voltage measured is not within the valid range, a class 2 message will be sent to the PCM to disable starting of the vehicle.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B2958 Security System Sensor Data Circuit High

Conditions for Setting the DTC

    • The ignition switch is ON.
    • The BCM signal input is greater than 4.9 volts for one second after turning the ignition switch to the CRANK position.

Action Taken When the DTC Sets

    • The DTC will set only when the engine is running.
    • The BCM will be in the fail enable mode allowing the vehicle to start and run.
    • The SECURITY indicator will be ON.

Conditions for Clearing the DTC

    • The current DTC will clear once an ignition cycle has occurred without the fault recurring.
    • After 100 concurrent ignition cycles occur without the fault recurring, a history DTC clears.
    • Using a scan tool

Diagnostic Aids

    • Use a scan tool in order to inspect the Passlock™ data voltage and the Passlock™ code.
    • Inspect the Passlock™ sensor harness for an intermittent or a short to battery. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • When directed to this table, DTC B2958 may have a history status.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Tests for proper operation of the circuit in the high voltage range.

  2. Tests for proper operation of the circuit in the low voltage range.

  3. Tests for high resistance or an open in the 12-volt reference circuit.

  4. Tests for a short to voltage, a high resistance, or an open in the signal circuit.

  5. Tests for high resistance or an open in the ground circuit.

Step

Action

Value(s)

Yes

No

Schematic Reference: Theft Deterrent System Schematics

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Momentarily rotate the ignition switch to CRANK, do not start the vehicle.
  3. Release the ignition switch to ON.
  4. With a scan tool, observe the Passlock™ Data Voltage in the body control module (BCM) Security Data List.

Does the scan tool indicate that the Passlock™ Data Voltage is within the specified range?

0.4-4.9 V

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the Passlock™ sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool observe the Passlock™ Data Voltage in the BCM Security Data List.

Does the scan tool indicate that the Passlock™ Data Voltage is greater than the specified value?

4.9 V

Go to Step 4

Go to Step 9

4

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the signal circuit of the Passlock™ sensor and the ground circuit of the Passlock™ sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool observe the Passlock™ Data Voltage in the BCM Security Data List.

Does the scan tool indicate that the Passlock™ Data Voltage is less than the specified value?

0.4 V

Go to Step 5

Go to Step 7

5

  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 12-volt reference circuit of the Passlock™ sensor and the ground circuit of the Passlock™ sensor.

Does the voltage measure less than the specified value?

12 V

Go to Step 6

Go to Step 11

6

Test the 12-volt reference circuit of the Passlock™ sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 9

7

Test the signal circuit of the Passlock™ sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 8

8

Test the ground circuit of the Passlock™ sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 9

9

Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 10

10

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 14

--

11

Inspect for poor connections at the Passlock™ sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

12

Replace the Passlock™ sensor in the ignition lock cylinder case. Refer to Ignition Lock Cylinder Case Replacement in Steering Wheel and Column.

Did you complete the replacement?

--

Go to Step 13

--

13

Perform the Programming Theft Deterrent System Components procedure.

Is the repair complete?

--

Go to Step 14

--

14

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition.
  3. Momentarily rotate the ignition switch to CRANK. Do not start the vehicle.
  4. Release the ignition switch to ON.
  5. Select the body control module display DTCs function on the scan tool.

Does the DTC reset?

--

Go to Step 3

Go to Step 15

15

Attempt to start the vehicle.

Does the engine start and run?

--

System OK

Go to Step 3