Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC C0186 00: Lateral Accelerometer CircuitDTC C0186 5A: Lateral Accelerometer Circuit Erratic
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Lateral Accelerometer Supply Voltage Circuit | C0186 00 | C0186 00 | C0186 00 | -- |
Lateral Accelerometer CAN Bus High Circuit | C0186 00 | C0186 00 | C0186 00 | C0186 5A |
Lateral Accelerometer CAN Bus Low Circuit | C0186 00 | C0186 00 | C0186 00 | C0186 5A |
Lateral Accelerometer Ground Circuit | -- | C0186 00 | -- | -- |
Circuit/System Description
The lateral accelerometer and the yaw rate sensors are combined into one sensor external to the electronic brake control module (EBCM). The Vehicle Stability Enhancement System (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The usable output signal is a serial data signal controller area network (CAN) high and CAN low serial data circuits.
Conditions for Running the DTC
The ignition switch is in the ON position.
Conditions for Setting the DTC
| • | The yaw/lateral combination sensor fails an internal self test. |
| • | Communication is lost between the EBCM and the yaw/lateral combination sensor. |
Action Taken When the DTC Sets
One or more of the following actions may occur:
| • | The VSES is disabled. |
| • | Traction control system (TCS) is disabled. |
| • | The TCS/VSES indicators turn ON. |
| • | The driver information center (DIC) displays the Service Traction Control, and or Service Stabilitrak message. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present. |
| • | The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Diagnostic Aids
Possible causes of this DTC are as follows:
| • | CAN HI and CAN LO circuits shorted together |
| • | CAN HI or CAN LO circuit shorted to ground |
| • | CAN HI or CAN LO circuit shorted to voltage |
Reference Information
Schematic Reference
Antilock Brake System Schematics
Connector End View Reference
Antilock Brake System Connector End Views
Description and Operation
Electrical Information Reference
Scan Tool Reference
Scan Tool Data List for EBCM
Circuit/System Verification
With scan tool installed, clear the DTCs then drive the vehicle in a straight line at a speed greater than 20 km/h (13 mph). If the DTC did not set as a current DTC see diagnostic aids.
Circuit/System Testing
- Ignition OFF, disconnect the yaw rate/lateral accelerometer connector.
- Test the yaw rate/lateral sensor reference voltage circuit for a short to voltage, short to ground, an open or high resistance.
- Test the yaw/lateral sensor ground circuit for an open or high resistance.
- Test the yaw/lateral sensor CAN HI and LO circuit for a short to voltage, short to ground, an open or high resistance.
- Ignition ON, test the yaw/lateral sensor reference voltage circuit for 12 volts, and the ground circuit for an open or high resistance.
| ⇒ | If the reference voltage circuit did not test normal, repair the circuit. |
| ⇒ | If the reference ground circuit did not test normal, repair the circuit. |
| ⇒ | If the yaw/later CAN HI and LO circuits did not test normal repair the circuit. |
| ⇒ | If the yaw/later 12-volt reference and ground circuits test normal replace the yaw/lateral sensor. |
| ⇒ | If the yaw/later 12-volt reference and ground circuits did not test normal replace the EBCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
