Brake Assist System Description and Operation. Chevrolet Avalanche

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2003 🢒 Avalanche - 4WD 🢒 Brakes 🢒 Hydraulic Brakes 🢒 Brake Assist System Description and Operation

Brake Assist System Description and Operation Hydraulic Assist


(1)	Master Cylinder
(2)	Power Brake Booster Outlet Hose
(3)	Power Brake Booster Inlet Pipe/Hose
(4)	Hydraulic Brake Booster
(5)	Power Steering Gear Inlet Pipe/Hose
(6)	Steering Gear
(7)	Power Steering Cooler
(8)	Power Steering Pump

System Component Description

The brake assist system consists of the following:

Brake Pedal: Receives, multiplies and transfers brake system input force from driver.

Brake Pedal Pushrod: Transfers multiplied input force received from brake pedal to brake booster.

Hydraulic Brake Booster: Uses power steering fluid pressure to decrease effort required by driver when applying brake system input force.

Power Steering System: Supplies pressurized power steering fluid used by hydraulic brake booster to decrease brake pedal effort.

System Operation

The hydraulic brake boost system uses fluid from the power steering pump (8) through the hydraulic boost inlet hose (3) and to the brake booster assembly (4). In addition to supplying the brake system with fluid for increased apply, the power steering pump is also connected to the power steering gear (6) and cooler (7).

The steering pump (8) is a continuous flow device supplying approximately 3 GPM at 1000 RPM, at the pump shaft. The fluid flows through the booster spool valve, then the return hose (5), and then to the steering gear (6). Pressure is produced by applying the brake pedal, resulting in the spool valve being actuated, internal to the hydraulic brake booster. The spool valve produces a marginal restriction that causes pressure in the booster (4) to rise and forces the power piston and therefore the output rod forward to generate force and motion at the master cylinder (1). The brake corners are actuated by the fluid impulse generated by the master cylinder (1). Internal blow by, or pressure relief, is directed to the low pressure return hose (2) back to the power steering pump (8).

Brake Assist System Description and Operation Vacuum Assist

System Component Description

The brake assist system consists of the following:

Brake Pedal: Receives, multiplies and transfers brake system input force from driver.

Brake Pedal Pushrod: Transfers multiplied input force received from brake pedal to brake booster.

Supplemental Brake Assist: The Supplemental Brake Assist (SBA) unit creates vacuum for the brake booster in case of a vacuum loss or low vacuum to the brake booster.

Vacuum Brake Booster: Uses source vacuum to decrease effort required by driver when applying brake system input force. When brake system input force is applied, air at atmospheric pressure is admitted to the rear of both vacuum diaphragms, providing a decrease in brake pedal effort required. When input force is removed, vacuum replaces atmospheric pressure within the booster.

Vacuum Source: Supplies force used by vacuum brake booster to decrease brake pedal effort.

Vacuum Source Delivery System: Enables delivery and retention of source vacuum for vacuum brake booster.

System Operation

Brake system input force is multiplied by the brake pedal and transferred by the pedal pushrod to the hydraulic brake master cylinder. Effort required to apply the brake system is reduced by the vacuum brake booster.

Supplemental Brake Assist

The Supplemental Brake Assist (SBA) unit creates vacuum for the brake booster in case of a vacuum loss or low vacuum to the brake booster. The SBA consists of

•	The sensor circuit board and pressure sensor

•	The check valve manifold

•	The vacuum pump

•

The motor

When the vehicle is keyed ON, the SBA performs a self test by toggling the Supplemental Brake Assist Signal Circuit low for one second. The instrument panel cluster (IPC) recognizes this as an indication that the SBA is functional. If the IPC does not see this signal for five consecutive ignition cycles the Service Brake Booster Message is displayed. The SBA performs diagnostics at 16 Km/h (10 mph) under normal conditions, and before 16 Km/h (10 mph) if a low vacuum condition exists. The SBA then spins the motor and runs diagnostics to determine if the pump is operating and the SBA is functional. The SERVICE BRAKE BOOSTER message will display until the next ignition cycle if the unit is unable to maintain reduced power brake levels.

The SBA unit utilizes the ignition on signal from the generator to determine the engine is running and monitors speed using an input from the vehicle speed sensor. It also has an internal pressure sensor that compares the pressure inside the booster to the ambient pressure. If the vacuum drops below 18 cm/Hg (7 in/Hg) the REDUCED BRAKE POWER message is displayed and a 5 second timer is started. If the vacuum stays below 18 cm/Hg (7 in/Hg) for 5 seconds the SBA starts the pump. If the vacuum drops below 15 cm/Hg (6 in/Hg) the pump comes on immediately. Once the vacuum level increases to 23 cm/Hg (9 in/Hg) The pump shuts off. The REDUCED BRAKE POWER message continues to be displayed until the vacuum level reaches 25 cm/Hg (10 in/Hg). If the pump runs for one minute without the vacuum reaching 23 cm/Hg (9 in/Hg) the pump shuts off and the SERVICE BRAKE BOOSTER message is displayed.

The SBA assembly operates in two modes.

•	Low Vacuum Mode -- The low vacuum mode can occur with the engine ON or OFF. The SBA determines the ON/OFF status by monitoring the regulator output on the engine ON circuit. This mode involves SBA pump activation and deactivation due to changes in vacuum detected by the pressure sensor.

-	Low Vacuum Engine ON Mode -- The SBA will operate in reaction to changes to brake booster vacuum as monitored by the pressure sensor. This mode is normally active on power up if a valid engine ON signal is detected and a low vacuum condition is indicated for more than 5 seconds.

-	Reduced Brake Power Mode -- When the booster vacuum drops below 18 cm/Hg (7 in/Hg) the SBA will start a 5 second timer. If the vacuum exceeds 18 cm/Hg (7 in/Hg) the timer stops and resets. After 5 seconds the pump activates and the REDUCED BRAKE POWER message is displayed.

-	Immediate Pump Activation Mode -- When the booster vacuum drops below 15 cm/Hg (6 in/Hg) the REDUCED BRAKE POWER message is displayed and the pump is turned on.

-	Pump Deactivation Mode -- The pump will be turned off when the booster vacuum exceeds 23 cm/Hg (9 in/Hg). The SBA will continue to display REDUCED BRAKE POWER until the booster vacuum exceeds 25 cm/Hg (10 in/Hg).

-	Low Vacuum Engine Off -- The SBA will monitor the vacuum when the vehicle is above 8 Km/h (5 mph) and an engine OFF condition is detected. If the vehicle is below 8 Km/h (5 mph) and an engine OFF condition is detected the SBA will monitor the vacuum for 60 seconds

•

Vacuum Augment (Engine OFF) Mode -- If the engine ON state changes to OFF after reaching 8 Km/h (5 mph) the SBA activates the pump for up to 60 seconds. After 60 seconds the pump shuts off and the SERVICE BRAKE BOOSTER message is displayed. If the engine ON signal is detected or the vehicle slows to below 8 Km/h (5 mph) before the pump times out. The pump shuts off and no message is displayed.