Refer to the scan tool manual for complete scan tool operating instructions.

ABS Motor

--

This function allows the technician to command the ABS pump motor On and Off.

Automated Bleed

--

The EBCM commands each valve solenoid and the pump motor ON and OFF in a special sequence in order to bleed air out of the BPMV. Refer to Antilock Brake System Automated Bleed Procedure for a step-by-step procedure.

Left Front Brake Apply

--

The EBCM enegizes the appropriate solenoids and the precharge pump motor to apply brake pressure to the left, front wheel. The precharge pump turns off after approximately 2 seconds, but the brake pressure is held for approximately 9 seconds. Refer to Brake Pressure Modulator Valve Hydraulic Testing for a step-by-step procedure.

Left Rear Brake Apply

--

The EBCM enegizes the appropriate solenoids and the precharge pump motor to apply brake pressure to the left, rear wheel. The precharge pump turns off after approximately 2 seconds, but the brake pressure is held for approximately 9 seconds. Refer to Brake Pressure Modulator Valve Hydraulic Testing for a step-by-step procedure.

Pre-charge Bleed

--

The EBCM commands both TC isolation valve solenoids on and energizes the precharge pump to bleed air from the precharge pump, combination valve and the hydraulic circuitry between these components. Refer to Antilock Brake System Automated Bleed Procedure for a step-by-step procedure.

Right Front Brake Apply

--

The EBCM enegizes the appropriate solenoids and the precharge pump motor to apply brake pressure to the right, front wheel. The precharge pump turns off after approximately 2 seconds, but the brake pressure is held for approximately 9 seconds. Refer to Brake Pressure Modulator Valve Hydraulic Testing for a step-by-step procedure.

Right Rear Brake Apply

--

The EBCM enegizes the appropriate solenoids and the precharge pump motor to apply brake pressure to the right, rear wheel. The precharge pump turns off after approximately 2 seconds, but the brake pressure is held for approximately 9 seconds. Refer to Brake Pressure Modulator Valve Hydraulic Testing for a step-by-step procedure.

Solenoid Tests

This function allows the technician to command a selected dump or isolation valve solenoid On and Off to verify proper operation of the BPMV. Refer to Brake Pressure Modulator Valve Hydraulic Testing for complete procedure instructions.

Request ABS/VSES Info. for SPS

Request Info.

This function allows you to request VIN and EBCM software information to be used when programming the EBCM using SPS.

Tire Size Calibration

Important: The Yaw Rate Reference Table Reset Procedure must also be performed if the tire size is changed. Refer to Yaw Rate Reference Table Resetting .

This function allows the technician to read the tire size calibration of the EBCM or calibrate the EBCM to the correct tire size. Calibration must be performed when the EBCM is replaced or when different size tires are installed on the vehicle.

Refer to the scan tool manual for complete scan tool operating instructions.

ABS Motor

--

This function allows the technician to command the ABS pump motor On and Off.

Automated Bleed

--

The EBCM commands each valve solenoid and the pump motor ON and OFF in a special sequence in order to bleed air out of the BPMV. Refer to Antilock Brake System Automated Bleed Procedure for a step-by-step procedure.

Function Test

--

The EBCM commands the system relay, valve solenoids and pump motor ON and OFF. The EBCM sets a DTC if a malfunction is detected.

Solenoid Tests

This function allows the technician to command a selected dump or isolation valve solenoid On and Off to verify proper operation of the BPMV. Refer to Brake Pressure Modulator Valve Hydraulic Testing for complete procedure instructions.

System Identification

--

The scan tool displays the hardware and software revision of the EBCM.

Tire Size Calibration

Important: The PCM must also be programmed with the correct tire size calibration when different size tires are installed on the vehicle. Refer to Service Programming System (SPS) in Programming.

This function allows the technician to read the tire size calibration of the EBCM or calibrate the EBCM to the correct tire size. Calibration must be performed when the EBCM is replaced or when different size tires are installed on the vehicle.

Low Trac Lamp

--

This function allows the technician to command the low traction indicator On and Off.

Traction Off Lamp

--

This function allows the technician to command the traction off indicator On and Off.

Requested Torque

--

This function allows the technician to turn Off engine torque reduction in order to verify proper operation of the Traction Control System.

Refer to the scan tool manual for complete scan tool operating instructions.

ABS Motor

--

This function allows the technician to command the ABS pump motor On and Off.

Automated Bleed

--

The EBCM commands each valve solenoid and the pump motor ON and OFF in a special sequence in order to bleed air out of the BPMV. Refer to Antilock Brake System Automated Bleed Procedure for a step-by-step procedure.

Function Test

--

The EBCM commands the system relay, valve solenoids and pump motor ON and OFF. The EBCM sets a DTC if a malfunction is detected.

Solenoid Tests

This function allows the technician to command a selected dump or isolation valve solenoid On and Off to verify proper operation of the BPMV. Refer to Brake Pressure Modulator Valve Hydraulic Testing for complete procedure instructions.

System Identification

--

The scan tool displays the hardware and software revision of the EBCM.

Tire Size Calibration

Important: The PCM must also be programmed with the correct tire size calibration when different size tires are installed on the vehicle. Refer to Service Programming System (SPS) in Programming.

This function allows the technician to read the tire size calibration of the EBCM or calibrate the EBCM to the correct tire size. Calibration must be performed when the EBCM is replaced or when different size tires are installed on the vehicle.