Circuit Description
The rear wheel steering control module monitors the rear wheel steering mode select switch 5-volt reference circuit for out of range voltage conditions. When the mode select switch button is depressed the switch is in the active state. When the mode select switch is released the switch is in the inactive state. The following conditions will help determine if there is a malfunctioning rear wheel steering mode select switch:
| • | The resistance of the load in the active state is 500 ohms with an additional 1,000 ohms pull-up resistor. |
| • | The resistance of the load in the inactive state is 2,000 ohms with an additional 1,000 ohms pull-up resistor. |
| • | The pull-up voltage is 12 volts. |
Conditions for Running the DTC
Turn ON the ignition, with engine ON.
Conditions for Setting the DTC
| • | The mode select switch 5-volt reference circuit is open, shorted to ground or voltage. |
| • | The mode select switch signal circuit is open or shorted to voltage. |
Action Taken When the DTC Sets
| • | The Service 4-Wheel Steer indicator on IPC will be displayed. |
| • | The code is displayed on the scan tool as DTC B3593. |
| • | The output to the motor is ramped down slowly at a rate of 1 degree/second back to center and held. |
| • | The rear wheels will be returned to the centered position. |
Conditions for Clearing the DTC
| • | The conditions for DTC are not currently present. |
| • | The module receives a clear code command from the scan tool. |
| • | The DTC clears after 100 malfunction free ignition cycles. |
Diagnostic Aids
| • | Inspect for poor connections at the harness connector of the rear wheel steering control module and Rear Wheel Steering Select Switch. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems. |
| • | Observe the rear wheel steering mode select switch. If all of the mode indicator LEDs are illuminated the rear wheel steering control module has lost its alignment memory settings and the scan tool must be used to re-calibrate the rear wheel steering alignment data in the rear wheel steering control module. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
The normal state of the switch is the state of the switch input before activation. The terminology used by the scan tool is OFF.
-
Tests for the proper operation of the switch in the normally open position.
-
Tests for the proper operation of the switch in the closed position.
-
Tests the 5-volt reference circuit for an open or a short to ground.
Step | Action | Value | Yes | No |
|---|---|---|---|---|
Schematic Reference: Rear Wheel Steering Schematics Connector End View Reference: Rear Wheel Steering Connector End Views | ||||
1 | Did you perform the Diagnostic System Check-Rear Wheel Steering? | -- | Go to Step 2 | |
Does the parameter change? | ON/OFF | Go to Diagnostic Aids | Go to Step 3 | |
Does the resistance measure within the specified parameter? | 1.8 kohms to 2.2 kohms | Go to Step 4 | Go to Step 14 | |
Does the resistance measure within the specified parameter? | 450 ohms- 550 ohms | Go to Step 5 | Go to Step 14 | |
5 |
Is the voltage at the 5-volt reference circuit within the specified parameter? | 4.750 to 5.00 V | Go to Step 7 | Go to Step 6 |
6 | Is the voltage at the 5-volt reference circuit less than the specified parameter? | 4.75 to 5.00 V | Go to Step 8 | Go to Step 9 |
7 |
Is the resistance at the mode select switch signal circuit less than the specified parameter? | 1500 ohms | Go to Step 12 | Go to Step 10 |
Test the 5-volt reference circuit of the rear wheel steer mode select switch for an open, or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 11 | |
9 | Test the 5-volt reference circuit of the rear wheel steer mode select switch for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 11 |
10 | Test the mode select switch signal circuit of the rear wheel steer mode select switch for an open, high resistance or short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 11 |
11 | Inspect for poor connections at the harness connector of the rear wheel steering control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 12 |
12 | Inspect for poor connections at the harness connector of the rear wheel steer mode select switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 15 | Go to Step 13 |
13 |
Important: Perform the Learn Alignment procedure. Refer to Wheel Alignment Measurement Replace the rear wheel steering control module. Refer to Rear Wheel Steering Control Module Replacement Did you complete the replacement? | -- | Go to Step 15 | -- |
14 | Replace the rear wheel steer mode select switch. Refer to Rear Wheel Steering Mode Switch Replacement . Did you complete the replacement? | -- | Go to Step 15 | -- |
15 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
