GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.

Warning: Refer to Collision Sectioning Warning in the Preface section.


    Object Number: 1708712  Size: SH

    Note: The door frame can be replaced at the factory seams, but requires the removal of the windshield, roof, and quarter panel. The sectioning procedures have been developed as a more cost-effective alternative to complete replacement. The specific area to be sectioned is determined by the extent of the damage to the vehicle.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove all related panels and components.
  4. Repair as much of the damage as possible to factory specifications. Refer to Dimensions - Body.
  5. Warning: Refer to Foam Sound Deadeners Warning in the Preface section.

  6. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  7. Perform additional sectioning procedures as necessary. Refer to the following procedures:
  8. •  Outer Windshield Frame Pillar Sectioning
    •  Rocker Outer Panel Sectioning
    •  Center Pillar Sectioning
    •  Rear Pillar Sectioning

    Object Number: 1769504  Size: SH
  9. Measure 70 mm (2 3/4 in) down from the large wiring harness hole in the hinge pillar (1). Mark a horizontal line.
  10. Note: Do not damage any inner panels or reinforcements.

  11. Cut the panel in the locations where sectioning is to be performed.

  12. Object Number: 1709182  Size: SH
  13. Locate and drill out all factory welds. Note the number and location of the welds for installation of the service part.

  14. Object Number: 1709183  Size: SH
  15. Remove the damaged hinge pillar.

  16. Object Number: 383364  Size: SH
  17. Cut and remove 30 mm (1 3/16 in) from the flanges on either side of the remaining section of the original piller. Cut 5 mm (3/16 in) wide gaps in the bottom corners.

  18. Object Number: 671573  Size: SH
  19. Step the tabs (1) inward to allow the door frame opening service section to fit over the original hinge pillar.

Installation Procedure


    Object Number: 1769505  Size: SH
  1. On the service body side, measure 40 mm (1 9/16 in) down from the large wiring harness hole in the hinge pillar. Mark a horizontal line. Cut the hinge pillar (1) along this line.
  2. Perform additional sectioning procedures as necessary to remove the unused areas of the service part.

  3. Object Number: 383381  Size: SH
  4. Drill 8 mm (5/16 in) plug weld holes along the sectioning cut on the remaining original part (2). Locate these holes approximately 25 mm (1 in) (a) from the edge and spaced 40 mm (1 ½ in) apart.

  5. Object Number: 1709185  Size: SH

    Note: If the location of the original plug weld holes cannot be determined, or if structural weld-thru adhesive was present, space the plug weld holes every 40 mm (1 1/2 in) apart.

  6. Drill 8 mm (5/16 in) plug weld holes in the service part, as necessary, in the locations noted from the original panel and along the sectioning cut.
  7. Prepare all attachment surfaces, as necessary.
  8. Apply GM-approved Weld-Thru Coating or equivalent to all mating surfaces. Refer to Anti-Corrosion Treatment and Repair.

  9. Object Number: 1709187  Size: SH
  10. Position the hinge pillar to the vehicle using 3-dimensional measuring equipment. Clamp in place.

  11. Object Number: 383389  Size: SH
  12. Plug weld accordingly.
  13. Note: To create a solid weld with minimum heat distortion, make 25 mm (1 in) stitch welds along the seam (2) with 25 mm (1 in) gaps between them. Complete the stitch weld.

  14. Clean and prepare all welded surfaces.
  15. Apply the sealers and anti-corrosion materials to the repair area (1), as necessary. Refer to Anti-Corrosion Treatment and Repair.
  16. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems.
  17. Install all related panels and components.
  18. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  19. Enable the SIR system. Refer to SIR Disabling and Enabling.