GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 28467-B (DW 117) Universal Engine Support Fixture

Removal Procedure


    Object Number: 1224503  Size: SH
  1. Remove the air cleaner assembly.
  2. Caution: Refer to Batteries Produce Explosive Gases Caution in the Preface section.

  3. Remove the battery and battery tray from the vehicle.
  4. Remove the shift cable pins (1).
  5. Remove the washers (2).
  6. Disconnect the select and the shift cable (3).
  7. Remove the cable E-rings (4).
  8. Disconnect the shift cables from the cable bracket.

  9. Object Number: 1224507  Size: SH
  10. Remove the engine wiring harness bending strap.
  11. Remove the ground wire bolt (2).
  12. Disconnect the ground wire (1).
  13. Disconnect the backup lamp switch connector (3).

  14. Object Number: 1240918  Size: SH
  15. Remove the radiator lower hose bolts (1).
  16. Disconnect the radiator lower hose (2).
  17. Remove the crankshaft position (CKP) sensor bolt (3).
  18. Disconnect the CKP sensor connector and remove the CKP sensor.

  19. Object Number: 1240920  Size: SH
  20. Disconnect the vehicle speed sensor (VSS) connector.
  21. Remove the VSS.
  22. Remove the starter motor.

  23. Object Number: 1291934  Size: SH

    Caution: While engine is operating, the exhaust system will become extremely hot. To prevent burns avoid contacting a hot exhaust system.

  24. Install J 28467-B  (1).

  25. Object Number: 1291935  Size: SH
  26. Remove the transaxle upper exhaust manifold side bolt (1) and the thermostat housing side bolt (2).

  27. Object Number: 1291936  Size: SH
  28. Drain the transaxle fluid.
  29. Remove the cable adjust nut (1).
  30. Disconnect the cable from the wire clip.
  31. Disconnect the clutch cable from the transaxle mount hole (2).

  32. Object Number: 1223641  Size: SH
  33. Remove the front under longitudinal frames and stabilizer. Refer to Stabilizer Shaft Replacement .
  34. Remove the drive axle, only from the transaxle side. Refer to Front Drive Axle Inner Shaft Replacement .
  35. Remove the clutch housing lower plate bolts (1) and lower plate (2).

  36. Object Number: 1291937  Size: SH

    Caution: While engine is operating, the exhaust system will become extremely hot. To prevent burns avoid contacting a hot exhaust system.

  37. Remove the front exhaust pipe nuts from the exhaust manifold side.
  38. Remove the gasket and separate the exhaust manifold pipe.
  39. Remove the front exhaust pipe.

  40. Object Number: 1291938  Size: SH
  41. Remove the 3 transaxle mounting bracket bolts.

  42. Object Number: 1240923  Size: SH
  43. Support the transaxle with a transaxle support jack.

  44. Object Number: 1291939  Size: SH
  45. Remove the damping block connection nut and bolt (2).
  46. Remove the 3 rear mounting bracket bolts (1).
  47. Remove the rear mounting bracket from the transaxle.

  48. Object Number: 1291940  Size: SH
  49. Remove the 2 rear damping block retaining bolts.
  50. Remove the rear damping block.

  51. Object Number: 1291941  Size: SH
  52. Remove the transaxle lower bolts (1, 2).

  53. Object Number: 1240923  Size: SH

    Notice: Support the engine in the normal position when removing the transaxle. Damage to related parts can occur.

  54. Remove the transaxle.
  55. Slide the transaxle sideways from the engine block.
  56. Lower the transaxle.

Installation Procedure


    Object Number: 1240923  Size: SH
  1. Support the transaxle with a transaxle support jack.
  2. Install the transaxle by inserting the transaxle input shaft into the clutch disc and sliding the transaxle sideways into the engine block.
  3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1291941  Size: SH
  4. Install the transaxle lower bolts (1, 2).
  5. Tighten
    Tighten the bolts to 55-65 N·m (41-48 lb ft).


    Object Number: 1291940  Size: SH
  6. Install the 2 rear damping block retaining bolts.
  7. Tighten
    Tighten the bolts to 50-60 N·m (37-44 lb ft).


    Object Number: 1291939  Size: SH
  8. Install the bracket, the 3 rear mounting bracket bolts (1), and the damping block connection nut.
  9. Tighten

        • Tighten the bracket bolts to 55-65 N·m (41-48 lb ft).
        • Tighten the connection nut and bolt to 75-85 N·m (55-63 lb ft).

    Object Number: 1291938  Size: SH
  10. Install the 3 rear transaxle mounting bracket bolts.
  11. Tighten
    Tighten the bolts to 45-55 N·m (33-41 lb ft).


    Object Number: 1291937  Size: SH
  12. Install the front exhaust pipe nuts.
  13. Tighten
    Tighten the nuts to 25-35 N·m (18-25 lb ft).


    Object Number: 1223641  Size: SH
  14. Install the clutch housing lower plate (2).
  15. Install the clutch housing lower plate bolts (1).
  16. Tighten
    Tighten the bolts to 8-12 N·m (71-106 lb in).

  17. Install the drive axle. Refer to Front Drive Axle Inner Shaft Replacement .
  18. Install the front under longitudinal frames and stabilizer. Refer to Stabilizer Shaft Replacement .

  19. Object Number: 1224509  Size: SH
  20. Install the clutch cable to the transaxle mount (2).
  21. Install the cable to the wire clip (1).
  22. Install the clutch cable adjusting nut (3).

  23. Object Number: 1291935  Size: SH
  24. Install the transaxle upper bolts (1, 2).
  25. Tighten
    Tighten the bolts to 55-65 N·m (41-48 lb ft).


    Object Number: 1291934  Size: SH
  26. Install the starter motor. Refer to Starter Motor Replacement .
  27. Remove J 28467-B  (1).

  28. Object Number: 1240920  Size: SH
  29. Install the VSS.
  30. Install the VSS mounting bolt.
  31. Tighten
    Tighten the bolt to 4-7 N·m (35-62 lb in).

  32. Connect the VSS connector.

  33. Object Number: 1240918  Size: SH
  34. Install the radiator lower hose and CKP sensor.
  35. Tighten

        • Tighten the hose bolt to 8-15 N·m (70-132 lb in).
        • Tighten the sensor bolt (3) to 5-8 N·m (44-70 lb in).

    Object Number: 1224507  Size: SH
  36. Connect the ground wire (1) and the backup lamp switch connector (3).
  37. Install the engine wiring harness bending strap.
  38. Tighten
    Tighten the bolt to 10-16 N·m (7-12 lb ft).


    Object Number: 1224503  Size: SH
  39. Connect the shift cables to the cable bracket.
  40. Install the cable E-rings (4).
  41. Connect the select and shift cable (3).
  42. Install the washers (2).
  43. Install the shift cable pins (1).

  44. Object Number: 1223658  Size: SH
  45. Install the drain plug (2).
  46. Tighten
    Tighten the drain plug to 25-30 N·m (18-22 lb ft).

  47. Remove the oil level plug (1).
  48. Fill recommended fluid to the proper level.
  49. Specification

        • The classification is 75W-85 (GL-4).
        • The capacity is 2.1 liters (2.21 quarts).
  50. Install the oil level plug (1).
  51. Tighten
    Tighten the oil level plug to 25-30 N·m (18-22 lb ft).

  52. Install the air cleaner assembly.
  53. Adjust the clutch cable.
  54. Caution: Refer to Batteries Produce Explosive Gases Caution in the Preface section.

  55. Install the battery and battery tray in the vehicle.