GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 28467-B (DW 117) Engine Support Fixture

Removal Procedure


    Object Number: 1248179  Size: SH
  1. Install the J 28467-B .
  2. Remove the battery and battery tray. Refer to Battery and Battery Tray Replacement in Engine Electrical.
  3. Remove the shift linkage assembly. Refer to Shift Linkage Adjustment .
  4. Remove the drive axle shaft. Refer to Front Drive Axle Inner Shaft Replacement in Front Drive Axle.

  5. Object Number: 1248184  Size: SH
  6. Disconnect the backup lamp switch electrical connector.
  7. Disconnect the speedometer speed sensor electrical connector.

  8. Object Number: 1248185  Size: SH
  9. Remove the clutch release cylinder retaining bolts and the clutch release cylinder.

  10. Object Number: 1248186  Size: SH
  11. Remove the damping block connection nut and bolt.
  12. Remove the 3 rear mounting bracket bolts.
  13. Remove the rear mounting bracket from the transaxle.

  14. Object Number: 1248188  Size: SH
  15. Remove the 2 rear damping block retaining bolts.
  16. Remove the rear damping block from the front cross member.

  17. Object Number: 1248189  Size: SH
  18. Remove the 2 cage retaining bolts.
  19. Remove the 3 transaxle upper mounting bracket bolts.
  20. Remove the upper mounting bracket and cage.

  21. Object Number: 1248191  Size: SH
  22. Remove the 3 transaxle upper retaining bolts.

  23. Object Number: 1248192  Size: SH
  24. Support the transaxle with a transaxle support jack.

  25. Object Number: 1248194  Size: SH
  26. Remove the 7 transaxle lower retaining bolts.

  27. Object Number: 1248195  Size: SH

    Important: Rest the transaxle only in an upright position

  28. Remove the transaxle.
  29. Slide the transaxle sideways away from the engine block.
  30. Lower the transaxle.

Installation Procedure


    Object Number: 1248195  Size: SH
  1. Support the transaxle with a transaxle support jack.
  2. Install the transaxle by inserting the transaxle input shaft into the clutch disc and sliding the transaxle sideways into the engine block.
  3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1245845  Size: SH
  4. Install the 7 transaxle lower retaining bolts.
  5. Tighten

        • Tighten the transaxle lower retaining bolts to 73 N·m (54 lb ft).
        • Tighten the transaxle lower retaining bolt to 31 N·m (23 lb ft).
        • Tighten the transaxle lower retaining bolt to 21 N·m (15 lb ft).

    Object Number: 1248197  Size: SH
  6. Install the three transaxle upper retaining bolts.
  7. Tighten
    Tighten the transaxle upper retaining bolts to 73 N·m (54 lb ft).


    Object Number: 1248198  Size: SH
  8. Install the cage retaining bolt and cage.
  9. Install the three transaxle upper mounting bracket bolts and bracket.
  10. Tighten
    Tighten the transaxle upper mounting bracket bolts to 60 N·m (44 lb ft).


    Object Number: 1248200  Size: SH
  11. Install the 2 rear damping block retaining bolts.
  12. Tighten
    Tighten the rear damping block retaining bolts to 55 N·m (41 lb ft).

  13. Install the rear damping block from the front cross member.

  14. Object Number: 1248201  Size: SH
  15. Install the 3 rear mounting bracket bolts and the bracket.
  16. Tighten
    Tighten the rear mounting bracket bolts to 80 N·m (59 lb ft).

  17. Install the damping block connection nut and bolt.
  18. Tighten
    Tighten the damping block connection nut and bolt to 80 N·m (59 lb ft).


    Object Number: 1248202  Size: SH
  19. Install the clutch release cylinder retaining bolts and the clutch release cylinder.
  20. Tighten
    Tighten the clutch release cylinder retaining bolts to 20 N·m (15 lb ft).


    Object Number: 1248184  Size: SH
  21. Connect the speedometer speed sensor electrical connector.
  22. Connect the backup lamp switch electrical connector.

  23. Object Number: 1248179  Size: SH
  24. Remove the J 28467-B .
  25. Install the drive axle shaft. Refer to Front Drive Axle Inner Shaft Replacement in Front Drive Axle.
  26. Install the shift linkage assembly. Refer to Shift Control Linkage Replacement .
  27. Install the battery and battery tray. Refer to Battery and Battery Tray Replacement in Engine Electrical.
  28. Inspect the fluid level. Refer to Transmission Fluid Level Inspection .