Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provide an overview of each diagnostic category. |
DTC Descriptors
DTC P1391: Rough Road Sensor PerformanceDTC P1392: Rough Road Sensor Circuit Low Voltage
DTC P1393: Rough Road Sensor Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
5-Volt Reference | P1392 | P1392 | P1393 | P1391 |
Rough Road Sensor Signal | P1392 | P1392 | P1393 | P1391 |
Low Reference | -- | P1391 | -- | P1391 |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine operating in Closed Loop Parameter Normal Range: 1.1-3.7 Volts | |||
5-Volt Reference | 0.0 Volts | 0.0 Volts | 5.0 Volts¹ |
Rough Road Sensor Signal | 0.0 Volts | 0.0 Volts | 5.0 Volts¹ |
Low Reference | -- | 0.0 Volts | 5.0 Volts¹ |
¹ Internal ECM or sensor damage may occur if the circuit is shorted to B+. | |||
Circuit/System Description
The rough road sensor is a vertical low G-acceleration sensor. By sensing vertical acceleration caused by rough road conditions, the engine control module (ECM) can determine if the changes in crankshaft speed are due to engine misfire or are driveline induced. If the rough road sensor detects a rough road condition, the ECM misfire detection diagnostic will be de-activated. The rough road sensor at rest output should be between 2.30-2.65 volts. During a rough road condition, the voltage output can vary between 0.5-4.5 volts. The rough road sensor is a capacitive type sensor with 3 circuits:
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
The ECM provides the rough road sensor with 5 volts on the 5-volt reference circuit and a ground on the low reference circuit. Vibration to the rough road sensor from rough road conditions in the road, provides the ECM with a signal voltage from less than 1 volt to greater than 4 volts.
Conditions for Running the DTC
P1391
| • | The engine has been running for greater than 10 seconds. |
| • | The vehicle speed is less than 5 km/h (3.1 mph). |
| OR |
| • | The engine has been running for greater than 10 seconds. |
| • | The vehicle speed is between 30-70 km/h (19-43 mph). |
| • | The DTC runs continuously when the above conditions are met. |
P1392 and P1393
| • | The engine has been running for greater than 10 seconds. |
| • | The DTCs run continuously when the above condition is met. |
Conditions for Setting the DTC
P1391
The ECM detects that the rough road sensor output is not within range.
P1392
The ECM detects that the rough road sensor voltage is less than 0.1 volt.
P1393
The ECM detects that the rough road sensor output is greater than 4.9 volts.
Action Taken When the DTC Sets
DTC P1391, P1392, and P1393 are Type C DTCs.
Conditions for Clearing the DTC
DTC P1391, P1392, and P1393 are Type C DTCs.
Diagnostic Aids
| • | If a shared 5-volt reference circuit is shorted to ground or shorted to a voltage, other 5-volt reference circuits may be affected. |
| • | The scan tool 5 volt reference parameter should display between 4.8-5.2 volts. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
- Ignition ON, observe the DTC information with a scan tool. Verify DTCs P0641 or P0651 are not set.
- Start the engine, observe the rough road sensor voltage parameter. The reading should be between 1.1-3.7 volts.
- If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records List.
| ⇒ | If either DTC is set, refer to DTC P0641 or P0651 . |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector of the rough road sensor.
- Ignition ON, verify that the rough road sensor parameter is less than 0.1 volt.
- Ignition ON, test for less than 0.2 volt between the low reference circuit and ground.
- Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit and ground.
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit and ground.
- Ignition ON, install a 3A fused jumper wire between the signal circuit and the 5-volt reference circuit. Verify that the rough road sensor parameter is greater than 4.8 volts.
- If all circuits/connections test normal, replace the rough road sensor.
| ⇒ | If greater than 0.1 volt, test the signal circuit of the rough road sensor for a short to voltage. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If greater than 0.2 volt, test the low reference circuit for a short to voltage. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If greater than 5 ohms, test the low reference circuit for an open/high resistance. If the circuit/connections test normal, replace the ECM. |
Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.
| ⇒ | If less than 4.8 volts, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the signal circuit for a short to ground or an open/high resistance. If the circuit/connections test normal, replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming |
