The manifold absolute pressure (MAP) sensor responds to pressure changes in the intake manifold. The pressure changes occur based on the engine load. The engine control module (ECM) supplies 5 volts to the MAP sensor on the 5-volt reference circuit. The ECM provides a ground on the low reference circuit. The MAP sensor provides a signal to the ECM on the MAP sensor signal circuit which is relative to the pressure changes in the manifold. The ECM detects a low signal voltage at a low MAP, such as during an idle or a deceleration. The ECM detects a high signal voltage at a high MAP, such as the ignition is ON, with the engine OFF, or at a wide open throttle (WOT). The MAP sensor is also used to determine the barometric pressure (BARO). This occurs when the ignition switch is turned ON, with the engine OFF. The BARO reading may also be updated whenever the throttle position (TP) sensor is greater than 28 percent.

The ECM detects that the actual MAP signal is not within the predicted range for greater than 25 seconds.

DTC P0106 is a Type B DTC.

DTC P0106 is a Type B DTC.

With the ignition ON and the engine stopped, the manifold pressure is equal to atmospheric pressure and the signal voltage will be high. This information is used by the ECM as an indication of vehicle altitude. Comparison of this reading with a known good vehicle with the same sensor is a good way to check the accuracy of a suspect sensor. Readings should be the same +0.4 volt.

The MAP sensor vacuum source should be thoroughly inspected for restrictions at the intake manifold.

Schematic Reference

Engine Controls Schematics

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

J 23738-A Vacuum Pump

1. Engine running, observe the scan tool MAP Sensor parameter. The reading should be between 32-42 kPa.

Important: The vehicle used for the comparison is not limited to the same type of vehicle being serviced. A vehicle known to provide an accurate reading is acceptable.

2. Ignition ON, compare the scan tool MAP sensor pressure parameter to the scan tool MAP sensor pressure parameter of a known good vehicle. The reading should be within 3 kPa of the known good vehicle.

Important: The Altitude vs Barometric Pressure table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or very low or very high temperature may cause a reading to be slightly out of range.

3. Ignition ON, compare the scan tool MAP sensor pressure parameter to the reading in the Altitude Versus Barometric Pressure . The MAP sensor pressure parameter should be within the specified range indicated on the table.
4. Engine running, the MAP sensor pressure parameter should change while starting the engine.
5. Engine running, snap the throttle while observing the scan tool MAP sensor pressure parameter. The reading should change rapidly when the throttle position changes.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Verify none of the following conditions exist:

•	Vacuum leaks or restrictions at the MAP sensor

•	Engine vacuum leaks

•	Restricted exhaust--Refer to Restricted Exhaust .

•	Worn piston rings--Refer to Engine Compression Test .

•	Incorrect cam timing--Refer to Timing Belt Inspection for the correct timing.

2. Ignition OFF, disconnect the harness connector at the throttle body assembly.
3. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal B and ground.

⇒	If greater than specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.

4. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Verify the scan tool TP sensor voltage parameter is less than 0.3 volt.

⇒	If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

6. Install a 3A fused jumper wire between the signal circuit terminal C and the 5-volt reference circuit terminal A. Verify the scan tool TP sensor voltage parameter is greater than 4.8 volts.

⇒	If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

7. Ignition OFF, connect the harness connector at the throttle body assembly.
8. Disconnect the harness connector at the MAP sensor.
9. Test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.

⇒	If greater than specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.

10. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

11. Verify the scan tool MAP sensor parameter is less than 12 kPa.

⇒	If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

12. Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool MAP sensor pressure parameter is greater than 102 kPa.

⇒	If less than the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

13. If all circuits test normal, test or replace the MAP sensor.

TP Sensor

1. Ignition OFF, disconnect the harness connector at the throttle body assembly.
2. Test for 1160-1175 ohms of resistance between the 5-volt reference terminal A and the low reference terminal B.

⇒	If not within the specified range, replace the throttle body assembly.

3. Test the resistance between the signal terminal C and the low reference terminal B. Sweep the TP sensor through the entire range. The resistance should vary between 1530-630 ohms without any spikes or dropouts.

⇒	If not within the specified range or is erratic, replace the throttle body assembly.

4. Apply 5 volts to the 5-volt reference circuit terminal A and ground to the low reference terminal B while monitoring the voltage between the signal terminal C and the low reference terminal B. Sweep the TP sensor through the entire range. The voltage should vary between 4.3-0.6 volts without any spikes or dropouts.

⇒	If not within the specified range or is erratic, replace the throttle body assembly.

MAP Sensor

1. Ignition OFF, perform one of the following applicable procedures.

•	Disconnect the vacuum supply hose from the MAP sensor

•	Remove the MAP sensor from the intake manifold

2. Ignition ON, observe and record the scan tool MAP sensor pressure data parameter. This is the first MAP sensor reading.
3. With the J 23738-A apply 5 in Hg (17 kPa) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure data parameter. This is the second MAP sensor reading.
4. Subtract the second MAP sensor reading from the first MAP sensor reading. Verify the vacuum decrease is within 1 in Hg (4 kPa) of the applied vacuum.

⇒	If not within the specified range, replace the MAP sensor.

5. With the J 23738-A apply 10 in Hg (34 kPa) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure data parameter. This is the third MAP sensor reading.
6. Subtract the third MAP sensor reading from the first MAP sensor reading. Verify the vacuum decrease is within 1 in Hg (4 kPa) of the applied vacuum.

⇒	If not with in the specified range, replace the MAP sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.