Power Steering Pump Replacement 1.2L LMU Engine

1. Use paint in order to place match marks on the pump and on the rear shackle.
2. Drain the power steering fluid by disconnecting the pressure and supply lines from the pump.
3. Remove the rear shackle bolt.
4. Remove the pump retaining bolt.
5. Disconnect the pressure switch connector.



6. Remove the front shackle bolt.
7. Remove the pump assembly.

1. Position the pump assembly in the vehicle.

Caution: Refer to Fastener Caution in the Preface section.




2. Loosely install the rear shackle bolt.
3. Loosely install the pump retaining bolt.
4. Position the belt on the pump pulley.
5. Align the match marks and adjust the tension on the belt.
6. Tighten the rear shackle bolt.

Tighten
Tighten the rear shackle bolt to 22 N·m (16 lb ft).

7. Tighten the pump retaining bolt.

Tighten
Tighten the pump retaining bolt to 22 N·m (16 lb ft).

8. Install the front shackle bolt.

Tighten
Tighten the front shackle bolt to 20 N·m (15 lb ft).

9. Connect the pressure and supply lines to the pump.

Tighten
Tighten the pressure line union nut to 28 N·m (21 lb ft).

10. Connect the pressure switch connector.

Caution: Refer to Using Proper Power Steering Fluid Caution in the Preface section.

11. Refill the pump with new fluid and bleed the air from the system. Refer to Power Steering System Bleeding.
12. Inspect for leaks. If leaks are found, correct the cause of the leaks and bleed the system.

Power Steering Pump Replacement 1.4L L95 and 1.5L LV8 Engines

1. Remove the air cleaner housing by removing the housing bolts and loosening the clamp.



2. Remove the pump drive belt from the pulley by moving the autotensioner.



3. Drain the power steering fluid by disconnecting the pressure and supply lines from the pump.
4. Remove the pump assembly by removing the steering pump retaining nuts.

Caution: Refer to Fastener Caution in the Preface section.




1. Install the pump to the A/C compressor bracket and tighten the steering pump retaining nuts.

Tighten
Tighten the steering pump retaining nuts to 25 N·m (18 lb ft).




2. Connect the pressure and supply lines to the power steering pump.

Tighten
Tighten the pressure line union nut to 28 N·m (21 lb ft).




3. Install the pump drive belt onto the pulley by moving the autotensioner.



4. Install the air cleaner housing with the housing bolts and the clamp.

Tighten
Tighten the air cleaner housing bolts to 12 N·m (106 lb in).

Caution: Refer to Using Proper Power Steering Fluid Caution in the Preface section.

5. Refill the pump with new fluid and bleed the air from the system. Refer to Power Steering System Bleeding.
6. Inspect for leaks. If leaks are found, correct the cause of the leak and bleed the system.

Power Steering Pump Replacement 1.4L LDT and 1.6L LXV Engines

1. Remove the power steering pump drive belt. Refer to Drive Belt Replacement for the 1.4L (LDT) engine or to Drive Belt Replacement for the 1.6L (LXV) engine.



2. Disconnect the pressure pipe (1) from the pump.
3. Disconnect the supply hose (2) from the pump.
4. Drain the power steering fluid.



5. Remove the bolts (1, 2) and the pump from the vehicle.

Caution: Refer to Steering Column in Lock Position Caution in the Preface section.




1. Install the pump and the bolts (1, 2). Tighten the bolts to 26 N·m (19 lb ft).



2. Install the supply hose (2) to the pump.
3. Install the pressure pipe (1) to the pump. Tighten the union nut to 28 N·m (21 lb ft).
4. Install the power steering pump drive belt. Refer to Drive Belt Replacement for the 1.4L (LDT) engine or to Drive Belt Replacement for the 1.6L (LXV) engine.
5. Fill the power steering fluid reservoir and bleed the power steering system. Refer to Power Steering System Bleeding.