Circuit Description
The intake air temperature (IAT) sensor uses a thermistor to control the signal voltage to the Powertrain Control Module (PCM). The PCM supplies a 5 volt reference and a ground to the sensor. When the air is cold the resistance is high, therefore the IAT signal voltage will be high. If the intake air is warm, resistance is low, therefore the IAT signal voltage will be low.
Conditions for Setting the DTC
| • | Engine run time is greater than 320 seconds. |
| • | Vehicle speed is less than 15 mph (24 km/h). |
| • | IAT is less than -40°C (-40°F). |
Action Taken When the DTC Sets
| • | The Malfunction Indicator Lamp (MIL) will illuminate. |
| • | The PCM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame and Failure Records buffers. |
| • | A history DTC is stored. |
| • | Coolant fan turns ON. |
| • | The PCM will default to 60°C (140°F) for intake air temperature. The scan tool will not the show the defaulted value. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF after three consecutive ignition cycles in which the diagnostic runs without a fault. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | The MIL/DTCs can be cleared by using the scan tool. |
Diagnostic Aids
| • | If the vehicle is at ambient temperature compare the IAT sensor to the ECT sensor. The IAT sensor and the ECT sensor should be relatively close to each other. |
| • | Use the Temperature vs. Resistance Values table, refer to Temperature vs Resistance to evaluate the possibility of a skewed sensor. |
| • | DTCs P0113 and P0121 set together indicate an open CKT 452. |
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
-
This step simulates a DTC P0112. If the PCM senses the change, the PCM and wiring are OK.
-
This step will determine if the reason the PCM did not sense the change was due to a open ground or signal circuit or faulty PCM.
-
Replacement PCM's must be reprogrammed. Refer to the latest Techline information for programming procedures.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | |||
2 |
Is the IAT sensor value less than the specified value? | -30° C (-22° F) | ||
3 |
Is the IAT sensor value less than the specified value? | -30° C (-22° F) | Go to Diagnostic Aids | |
Is the IAT sensor value greater than the specified value? | 130° C (266° F) | |||
Jumper the IAT sensor signal circuit to ground. Is the IAT sensor value greater than the specified value? | 130° C (266° F) | |||
6 | Check for a poor connections at the IAT sensor electrical connector and replace any faulty terminals if necessary. Was a repair necessary? | -- | ||
7 | Check the IAT sensor ground circuit for an open and repair as necessary. Was a repair necessary? | -- | ||
8 | Check the IAT sensor signal circuit for an open and repair as necessary. Was a repair necessary? | -- | ||
9 | Check for a poor IAT sensor ground or a poor IAT sensor signal circuit terminal connection at the PCM and repair if necessary. Was a repair necessary? | -- | ||
10 | Replace the IAT sensor. Is the action complete? | -- | -- | |
Replace the PCM. Is the action complete? | -- | -- | ||
12 |
Does the scan tool indicate that this diagnostic has ran and passed? | -- | ||
13 | Check if any additional DTCs are set. Are any DTCs displayed that have not been diagnosed? | -- | Go to applicable DTC table | System OK |
