Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every 2 seconds. When no message is detected from a learned identification number for 5 seconds, a DTC U1xxx where xxx is equal to the 3-digit identification number is set.
The control module ID number list below provides a method for determining which module is not communicating. A module with a class 2 serial data circuit malfunction or which loses power during the current ignition cycle will have a Loss of Communication DTC set by other modules that depend on information from that failed module. The modules that can communicate will set a DTC indicating the module that can not communicate.
Control Module | ID Number |
|---|---|
Powertrain Control Module (PCM) | 016 |
Transfer Case Shift Control Module (TCSCM) | 026 |
Electronic Brake Control Module (EBCM) | 041 |
Body Control Module (BCM) | 064 |
Inflatable Restraint Sensing and Diagnostic Module (SDM) | 088 |
Instrument Panel Cluster (IPC) | 096 |
Driver Information Center (DIC) | 097 |
Radio | 128 |
Memory Seat Module (MSM) - Driver | 166 |
When more than one Loss of Communication DTC is set in either one module or in several modules, diagnose the DTCs in the following order:
- Current DTCs before history DTCs unless told otherwise in the diagnostic table.
- The DTC which is reported the most times.
- From the lowest number DTC to the highest number DTC.
Conditions for Running the DTC
| • | The following diagnostic trouble codes do not have a current status: |
| - | U1300 |
| - | U1301 |
| - | U1305 |
| • | The vehicle power mode requires serial data communication to occur. |
Conditions for Setting the DTC
A message from a learned identification number has not been detected for the past 5 seconds.
Action Taken When the DTC Sets
The module uses a default value for the missing parameter.
Conditions for Clearing the DTC
| • | A current DTC clears when the malfunction is no longer present. |
| • | A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction. |
Diagnostic Aids
| • | An intermittent open between the inoperative module and a star connector may cause this code to set. |
| • | A poor connection at the inoperative module or a star connector may cause this code to set. |
| • | An intermittent open in a star connector may cause this code to set. |
| • | An improperly powered module may cause this code to set. |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Yes | No | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Data Link Connector Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems | |||||||||||||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||||||||||||||
2 |
Important: Use the control module ID number list in order to determine which module is not communicating. Test the following circuits of the module that is not communicating for an open or a short to ground:
Refer to the following:
Did you find and correct the condition? | Go to Step 7 | Go to Step 3 | ||||||||||||||||||||
3 |
Refer to the following:
Did you find and correct the condition? | Go to Step 7 | Go to Step 4 | ||||||||||||||||||||
4 | Test the class 2 serial data circuits of the module that is not communicating for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 7 | Go to Step 5 | ||||||||||||||||||||
5 | Inspect the harness connectors of the module that is not communicating for poor connections and terminal tension at the following circuits:
Refer to the following:
Did you find and correct the condition? | Go to Step 7 | Go to Step 6 | ||||||||||||||||||||
6 | Replace the module which is not communicating. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 7 | -- | ||||||||||||||||||||
Does the scan tool display any DTCs which do not begin with a "U"? | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | Go to Step 8 | |||||||||||||||||||||
8 | Select the Display DTCs function for the modules which had the Loss of Communications DTC set. Does the scan tool display any DTCs which do not begin with a "U"? | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | Go to Step 9 | ||||||||||||||||||||
9 |
Did you complete the action? | System OK | -- | ||||||||||||||||||||
