Stop Lamps Inoperative - One Pickup
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |
2 | Verify that one of the stoplamps is inoperative. Do the stoplamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Is the bulb filament open? | -- | Go to Step 7 | Go to Step 4 |
4 | Connect a J 39200 Digital Multimeter (DMM) between terminal G of the inoperative lamp socket and ground and check for continuity. Refer to Circuit Testing in Wiring Systems. Is continuity present? | -- | Go to Step 6 | Go to Step 5 |
5 | Locate and repair the open or high resistance in CKT 1750 (BLK) or CKT 2250 (BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
6 |
Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 8 |
7 | Replace the bulb. Is the repair complete? | -- | Go to Step 13 | -- |
8 | Test for open, high resistance or short to ground in CKT 618 (YEL) (LH side) or CKT 619 (DK GRN) (RH side). Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 9 | Go to Step 10 |
9 | Repair the open, high resistance or short to ground in CKT 618 (YEL) (LH side) or CKT 619 (DK GRN) (RH side). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
10 | Test for open or high resistance in CKT 1418 (YEL/BLK) (LH side) or CKT 1419 (DK GRN/WHT) (RH side). Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 11 | Go to Step 12 |
11 | Repair the open or high resistance in CKT 1418 (YEL/BLK) (LH side) or CKT 1419 (DK GRN/WHT) (RH side). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
12 | Replace the Multifunction Switch (Turn Signal Switch). Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Standard or Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt. Is the repair Complete? | -- | Go to Step 13 | -- |
13 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
Stop Lamps Inoperative - One Utility
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |
2 | Verify that one of the stoplamps is inoperative. Do the stop lamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Is the bulb open? | -- | Go to Step 7 | Go to Step 4 |
4 | Connect a J 39200 Digital Multimeter (DMM) between ground and cavity G of the inoperative lamp socket. Refer to Circuit Testing in Wiring Systems. Is there continuity? | -- | Go to Step 6 | Go to Step 5 |
5 | Locate and repair the open or high resistance in CKT 1350 (BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
6 |
Does the test lamp light? | -- | Go to Step 7 | Go to Step 8 |
7 | Replace the bulb. Is the repair complete? | -- | Go to Step 13 | -- |
8 | Test for open, high resistance or short to ground in CKT 618 (YEL) (LH side) or CKT 619 (DK GRN) (RH side). Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 9 | Go to Step 10 |
9 | Repair open, high resistance or short to ground in CKT 618 (YEL) (LH side) or CKT 619 (DK GRN) (RH side). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
10 | Test for open or high resistance in CKT 1418 (YEL/BLK) (LH side) or CKT 1419 (DK GRN/WHT) (RH side). Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 11 | Go to Step 12 |
11 | Repair open or high resistance in CKT 1418 (YEL/BLK) (LH side) or CKT 1419 (DK GRN/WHT) (RH side). Refer to Circuit Testing in Wiring Systems. Is the repair complete? | -- | Go to Step 13 | -- |
12 | Replace the Multifunction Switch (Turn Signal Switch). Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Standard or Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt. Is the repair Complete? | -- | Go to Step 13 | -- |
13 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
Stop Lamps Inoperative - One Export
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |
2 | Verify that the stoplamps are inoperative. Do the stop lamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Does the High Mount Stop Lamp operate properly? | -- | Go to Step 4 | |
4 | Inspect the inoperative bulb for an open filament. Was a problem found? | -- | Go to Step 5 | Go to Step 6 |
5 | Replace the defective bulb. Is the repair complete? | -- | Go to Step 9 | -- |
6 | Connect a test lamp from ground to terminal A of the inoperative Tail/Stoplamp socket and apply the service brake. Refer to Circuit Testing in Wiring Systems. Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 8 |
7 | Locate and repair the open or high resistance in CKT 1350 (BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- |
8 | Locate and repair the open or high resistance in CKT 1320 (LT BLU). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- |
9 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
