GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Blazer - 4WD 🢒 Engine 🢒 Engine Controls - 4.3L 🢒 DTC P0137

Circuit Description

The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high, and decreases the signal voltage as the engine runs leaner. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.

The HO2S contains a heater that is necessary in order to quickly warm the sensor to the operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. The control module also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel control operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or lean out the mixture, when the HO2S detects a rich exhaust condition.

This diagnostic trouble code (DTC) is designed to detect an HO2S voltage that remains low for more than a specified number of seconds during the test conditions.

Conditions for Running the DTC
    • DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0200, P0300, P0440, P0442, P0446, P0452, P0453, or P1441 are not set.
    • The ignition 1 signal is between 9-18 volts.
    • The fuel tank level remaining is more than 10 percent.
    • The loop status is Closed.
    • Intrusive tests are not in progress.
    • Scan tool output controls are not active.

Lean Test Enable

    • The air fuel ratio is between 14.5:1-14.7:1.
    • The throttle position (TP) is between 3-70 percent.

Power Enrichment Test Enable

    • Power enrichment is active.
    • The above condition is met for 2 second.

Conditions for Setting the DTC

Lean Test

The HO2S voltage is less than 25 mV for 240 seconds.

Power Enrichment Test

The HO2S voltage is less than 600 mV for 10 seconds.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

Important: Remove any debris from the powertrain control module (PCM) connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing or replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.

    • Inspect the HO2S wire. The sensor pigtail may be in contact with the exhaust manifold or with the exhaust system.
    • Check the HO2S oxygen supply. An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provide the supply of oxygen. Inspect the HO2S wires and connections for breaks or contamination. Refer to Heated Oxygen Sensor Wiring Repairs in Wiring Systems.
    • Check for an intermittent ground in the signal wire between the connector and the sensor. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • Inspect the lean injectors. Perform the Injector Balance Test. Refer to Fuel Injector Balance Test with Tech 2 or Fuel Injector Balance Test with Special Tool .
    • Check for fuel contamination. Water near the in-tank fuel pump inlet can be delivered to the injectors. The water causes a lean exhaust and can set a DTC. Refer to Fuel Injector Balance Test with Tech 2 .
    • Check the fuel pressure. The system will be lean if the fuel pressure is low. Refer to Fuel System Diagnosis .
    • Check for exhaust leaks. An exhaust leak near the HO2S can cause a lean condition. Refer to Exhaust Leakage in Engine Exhaust.
    • Check for vacuum leaks or for crankcase leaks that can cause a lean condition.
    • If the components listed above are OK, the HO2S may be at fault.
    • For an intermittent condition, refer to Symptoms - Engine Controls .

Test Description

The number below refers to the step number on the diagnostic table.

  1. Monitor the HO2S voltage of the opposite bank sensor. If the voltage activity of the opposite bank sensor is similar to the voltage activity of the suspect sensor, check for lean conditions that would affect both cylinder banks. An opposite bank sensor with normal HO2S voltage activity indicates the suspect HO2S needs replacement or a lean condition exists only on the suspect HO2S cylinder bank.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2
  1. Run the engine until the engine reaches the normal operating temperature.
  2. Using the scan tool, monitor the HO2S voltage for the sensor that applies to this DTC.

Is the HO2S voltage fixed less than the value specified?

25 mV

Go to Step 5

Go to Step 3

3

  1. Change the throttle position more than 5 percent within 1 second, 6 times.
  2. Observe the affected HO2S voltage with a scan tool.

Is the HO2S voltage within the specified range?

350-550 mV

Go to DTC P0140

Go to Step 4

4

The condition that set this DTC is not present. This DTC may have been set by one of the following conditions:

    • A high signal wire intermittently shorted to engine ground or to the HO2S low reference circuit
    • HO2S connector water intrusion
    • An exhaust leak between the HO2S and the engine--Refer to Exhaust Leakage in Engine Exhaust.
    • An intermittent lean engine condition such as the following:
       - A vacuum leak
       - An incorrect or defective positive crankcase ventilation (PCV) valve or system
       - Incorrect fuel pressure
       - Lean fuel injectors
       - An inaccurate mass air flow (MAF) sensor
       - A lean engine condition during Power Enrichment operation

Repair any of the above or similar engine conditions as necessary.

Did you find and correct the condition?

--

Go to Step 11

Go to Diagnostic Aids

5
  1. Turn OFF the ignition.
  2. Disconnect the HO2S connector for the sensor that applies to this DTC.
  3. Turn ON the ignition, with the engine OFF.
  4. Using the scan tool, monitor the HO2S voltage for the sensor that applies to this DTC.

Is the HO2S voltage within the specified value range?

351-551 mV

Go to Step 6

Go to Step 7

6
  1. The HO2S may be detecting a lean exhaust condition. Check for one of the following conditions:
    2. • HO2S connector water intrusion
    • An exhaust leak between the HO2S and the engine--Refer to Exhaust Leakage in Engine Exhaust.
    • Vacuum leaks
    • Incorrect fuel pressure
    • Lean fuel injectors
    • An inaccurate MAF sensor
  2. Repair any of the above or similar engine conditions as necessary.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 9

7
  1. Turn OFF the ignition.
  2. Disconnect the PCM connector that contains the HO2S high signal circuit.
  3. Using a DMM, measure and record the resistance between the HO2S high signal circuit and ground.
  4. Measure and record the resistance between the HO2S high signal circuit and the HO2S low reference circuit.

Is the resistance at the specified value on both tests?

∞

Go to Step 10

Go to Step 8

8

Repair the HO2S signal high circuit shorted to ground or shorted to the HO2S low circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 11

--

9

Replace the HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 .

Did you complete the replacement?

--

Go to Step 11

--

10

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 11

--

11
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC run and pass?

--

Go to Step 12

Go to Step 2

12

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK