GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 41427 Engine Lift Bracket

Removal Procedure

Notice: If the engine is damaged internally and a new engine assembly is installed in the vehicle, ensure that all foreign material is flushed out of the cooling system. You must also flush out the oil cooler system. Failure to rid the oil cooler system of debris can result in engine damage.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Drain the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  3. Drain the engine oil. Refer to Engine Oil and Oil Filter Replacement .
  4. Remove the hood. Refer to Hood Replacement in Body Front End.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  6. Remove the underbody shields, if equipped.
  7. Remove the exhaust pipe from the exhaust manifolds. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
  8. Remove the engine oil cooler pipes. Refer to Engine Oil Cooler Hose/Pipe Replacement in Engine Cooling.

  9. Object Number: 449304  Size: SH
  10. Remove the stud holding the starter wire harness and if equipped, transmission oil cooler lines.
  11. Remove the starter. Refer to Starter Motor Replacement in Engine Electrical.

  12. Object Number: 334324  Size: SH
  13. Remove the transmission cover.
  14. Remove the transmission.
  15. • Refer to Transmission Replacement in Automatic Transmission - 4L60-E.
    • Refer to Transmission Replacement in Manual Transmission - NV 3500.

    Object Number: 4564  Size: SH
  16. Remove the front engine mount through bolts.
  17. Lower the vehicle.

  18. Object Number: 172994  Size: SH
  19. Remove the PCV tube from the right valve rocker arm cover and the air cleaner outlet duct.

  20. Object Number: 444792  Size: SH
  21. Disconnect the breather tube at the air cleaner outlet duct.

  22. Object Number: 312278  Size: SH
  23. Remove the air cleaner outlet duct retaining wingnut.

  24. Object Number: 10940  Size: SH
  25. Disconnect the intake air temperature (IAT) sensor harness connector.

  26. Object Number: 424556  Size: SH
  27. Remove the air cleaner outlet duct from the throttle body.

  28. Object Number: 325556  Size: SH

    Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable whenever you remove the engine from the vehicle.

    In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.

  29. Disconnect the accelerator cable from the throttle body.

  30. Object Number: 616725  Size: SH
  31. Remove the accelerator cable from the accelerator control cable bracket.
  32. Remove the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. Refer to Cruise Control Cable Replacement in Cruise Control.
  33. Remove the radiator. Refer to Radiator Replacement in Engine Cooling.
  34. Remove the inlet and outlet radiator hoses from the engine. Refer to Radiator Inlet Hose Replacement and Radiator Outlet Hose Replacement in Engine Cooling.
  35. Disconnect the heater hoses from the engine. Refer to Heater Inlet Hose Replacement and Heater Outlet Hose Replacement in Heating, Ventilation and Air Conditioning.

  36. Object Number: 346148  Size: SH
  37. Disconnect the power brake booster vacuum hose from the intake manifold.
  38. Disconnect the vacuum hose for the A/C system, if equipped from the intake manifold.

  39. Object Number: 516898  Size: SH
  40. Disconnect the following electrical connectors:
  41. • The A/C compressor clutch (1), if equipped
    • The A/C compressor cutoff switch (5), if equipped
    • The TP sensor (2)
    • The IAC valve motor (3)
    • The ECT sensor (4)

    Object Number: 516916  Size: SH
  42. Disconnect the following electrical connectors:
  43. • The fuel meter body (1)
    • The EVAP canister purge solenoid (2)
    • The MAP sensor (3)

    Object Number: 516938  Size: SH
  44. Disconnect the following electrical connectors:
  45. • The ICM (1)
    • The ignition coil (2)
    • The generator (4)

    Object Number: 516981  Size: SH
  46. Disconnect the following electrical connectors:
  47. • The distributor (1)
    • The engine oil pressure sensor (2)
    • The knock sensor (3)

    Object Number: 517077  Size: SH
  48. Disconnect the CKP sensor (2) electrical connector.
  49. Remove the bolt and the battery negative cable (1).
  50. Remove the engine wiring harness bracket bolt (3).
  51. Remove the engine wiring harness clips from the front of the engine.
  52. Remove the engine wiring harness clips from the brackets.
  53. Move the engine wiring harness aside.
  54. Remove the generator. Refer to Generator Replacement in Engine Electrical.

  55. Object Number: 555709  Size: SH
  56. Remove the bolt holding the ground wires to the left cylinder head.
  57. Remove the bolt holding the fuel pipe bracket to the rear of left cylinder head.

  58. Object Number: 375426  Size: SH
  59. Remove the bolts holding the ground wires to the right cylinder head.

  60. Object Number: 395663  Size: SH
  61. Remove the bolt holding the ground strap to the right cylinder head.

  62. Object Number: 339439  Size: SH
  63. Remove the accelerator control cable bracket from the throttle body.
  64. Remove the water pump pulley. Refer to Water Pump Replacement in Engine Cooling.
  65. Remove the A/C compressor, if equipped. Refer to Air Conditioning Compressor Replacement in Heating, Ventilation, and Air Conditioning.

  66. Object Number: 288833  Size: SH
  67. Remove the nuts holding the power steering pump rear bracket to the engine.
  68. Remove the power steering pump mounting bracket.
  69. • The power steering pump can remain on the mounting bracket.
    • The hoses do not require removal.
    • Remove the three bolts and the nut.
    • Slide the mounting bracket off of the stud.
    • Secure the mounting bracket out of the way.
  70. Remove the distributor cap. Refer to Distributor Replacement in Engine Controls - 4.3L.
  71. Disconnect the fuel pipes at the rear of the intake manifold. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls - 4.3L.
  72. Disconnect the EVAP canister purge solenoid valve pipe. Refer to Evaporative Emission Hoses/Pipes Replacement - Engine in Engine Controls - 4.3L.
  73. Remove the water outlet. Refer to Engine Coolant Thermostat Replacement in Engine Cooling.

  74. Object Number: 33636  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  75. Attach the J 41427 to the left front and the right rear intake manifold mounting bolts, using the following procedure:
  76. 52.1. Remove the right rear lower intake manifold bolts.
    52.2. Install the J 41427 marked RIGHT REAR.
    52.3. Install the retaining bolts.
    52.4. Remove the left front lower intake manifold bolts.
    52.5. Install the J 41427 marked LEFT FRONT with the arrow pointing to the front of the engine.
    52.6. Install the retaining bolts.

    Tighten
    Tighten the retaining bolts to 15 N·m (11 lb ft).

  77. Install a engine lifting device to the engine lift brackets.
  78. Remove the engine.

Installation Procedure

Notice: If the engine is damaged internally and a new engine assembly is installed in the vehicle, ensure that all foreign material is flushed out of the cooling system. You must also flush out the oil cooler system. Failure to rid the oil cooler system of debris can result in engine damage.


    Object Number: 33636  Size: SH
  1. Attach the J 41427 to the left front and the right rear intake manifold mounting bolts, using the following procedure:
  2. 1.1. Remove the right rear lower intake manifold bolts.
    1.2. Install the J 41427 marked RIGHT REAR.
    1.3. Install the retaining bolts.
    1.4. Remove the left front lower intake manifold bolts.
    1.5. Install the J 41427 marked LEFT FRONT with the arrow pointing to the front of the engine.
    1.6. Install the retaining bolts.

    Tighten
    Tighten the retaining bolts to 15 N·m (11 lb ft).

  3. Install a engine lifting device to the engine lift brackets.
  4. Install the engine into the vehicle.

  5. Object Number: 4564  Size: SH
  6. Install the engine mount through-bolts and nuts.
  7. Tighten
    Tighten the engine mount through-bolts or the nuts to the following:

    • Tighten the through-bolts to 74 N·m (55 lb ft)
    • Tighten the nuts to 63 N·m (46 lb ft)
  8. Remove the J 41427 and the engine lifting device.
  9. Apply thread lock GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the threads of the lower intake manifold bolts.
  10. Install the intake manifold bolts.
  11. Tighten

    1. Tighten the bolts the first pass to 3 N·m (27 lb in).
    2. Tighten the bolts the second pass to 12 N·m (106 lb in).
    3. Tighten the bolts the third pass to 15 N·m (11 lb ft).
  12. Install the water outlet. Refer to Engine Coolant Thermostat Replacement in Engine Cooling.
  13. Connect the fuel pipes at the rear of the engine. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls - 4.3L.
  14. Install the distributor cap. Refer to Distributor Replacement in Engine Controls - 4.3L.
  15. Connect the EVAP canister purge solenoid valve pipe. Refer to Evaporative Emission Hoses/Pipes Replacement - Engine in Engine Controls - 4.3L.

  16. Object Number: 288833  Size: SH
  17. Install the power steering pump mounting bracket.
  18. • Slide the power steering pump mounting bracket on the stud.
    • Position the power steering pump rear bracket on the studs.
    • Install the power steering pump mounting bracket three bolts and the nut.
    • Install the nut for the power steering pump rear bracket to the front of the engine.

    Tighten
    Tighten the power steering pump mounting bracket and the power steering pump rear bracket bolts and the nuts to 41 N·m (30 lb ft).

  19. Install the A/C compressor, if equipped. Refer to Air Conditioning Compressor Replacement in Heating, Ventilation and Air Conditioning.
  20. Install the water pump pulley. Refer to Water Pump Replacement in Engine Cooling.

  21. Object Number: 339439  Size: SH
  22. Install the accelerator control cable bracket to the throttle body.
  23. Tighten
    Tighten the bolt to 9 N·m (80 lb in).


    Object Number: 555709  Size: SH
  24. Install the bolt holding the ground wires to the left cylinder head.
  25. Tighten
    Tighten the ground wire bolt to 35 N·m (26 lb ft).

  26. Install the bolt holding the fuel pipe bracket to the rear of the left cylinder head.
  27. Tighten
    Tighten the fuel pipe bracket bolt to 30 N·m (22 lb ft).


    Object Number: 375426  Size: SH
  28. Install the stud holding the ground wires to the right cylinder head.
  29. Tighten
    Tighten the ground wire stud to 35 N·m (26 lb ft).


    Object Number: 395663  Size: SH
  30. Install the bolt and the ground strap to the rear of the right cylinder head.
  31. Tighten
    Tighten the ground strap bolt to 35 N·m (26 lb ft).


    Object Number: 517077  Size: SH
  32. Position the engine wiring harness.
  33. Install the engine wiring harness clips to the brackets.
  34. Install the engine wiring harness clips to the front of the engine.
  35. Connect the CKP sensor electrical connector (2).
  36. Install the bolt and the battery negative cable (1).
  37. Tighten
    Tighten the bolt to 17 N·m (13 lb ft).

  38. Install the engine wiring harness bracket bolt (3) to the generator mounting bracket.
  39. Tighten
    Tighten the stud to 25 N·m (18 lb ft).

  40. Install the generator. Refer to Generator Replacement in Engine Electrical.

  41. Object Number: 516981  Size: SH
  42. Connect the following electrical connectors:
  43. • The distributor (1)
    • The engine oil pressure sensor (2)
    • The knock sensor (3)

    Object Number: 516898  Size: SH
  44. Connect the following electrical connectors:
  45. • The A/C compressor clutch (1), if equipped
    • The A/C compressor cutoff switch (5), if equipped
    • The TP sensor (2)
    • The IAC valve motor (3)
    • The ECT sensor (4)

    Object Number: 516916  Size: SH
  46. Connect the following electrical connectors:
  47. • The fuel meter body (1)
    • The EVAP canister purge solenoid (2)
    • The MAP sensor (3)

    Object Number: 516938  Size: SH
  48. Connect the following electrical connectors:
  49. • The ICM (1)
    • The ignition coil (2)
    • The generator (4)

    Object Number: 346148  Size: SH
  50. Connect the power brake booster vacuum hose to the intake manifold.
  51. Connect the vacuum hose for the A/C system, if equipped.
  52. Install the cruise control cable, if equipped to the throttle shaft and the accelerator cable bracket. Refer to Cruise Control Cable Replacement in Cruise Control.

  53. Object Number: 325556  Size: SH

    Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable whenever you remove the engine from the vehicle.

    In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.

  54. Install the NEW accelerator cable onto the throttle body.

  55. Object Number: 616716  Size: SH
  56. Wrap the cable in between the finger of the hook tab and the pulley wall. Make sure that the cable is fully seated in the pulley groove. The cable must not lie outside of the hook tab.

  57. Object Number: 616725  Size: SH
  58. Install the accelerator cable to the accelerator cable control bracket.
  59. Install the radiator. Refer to Radiator Replacement in Engine Cooling.
  60. Install the inlet and outlet radiator hoses to the engine. Refer to Radiator Inlet Hose Replacement and Radiator Outlet Hose Replacement in Engine Cooling.
  61. Connect the heater hoses to the engine. Refer to Heater Inlet Hose Replacement and Heater Outlet Hose Replacement in Heating, Ventilation and Air Conditioning.
  62. Raise the vehicle.
  63. Install the transmission.
  64. • Refer to Transmission Replacement in Automatic Transmission - 4L60-E.
    • Refer to Transmission Replacement in Manual Transmission - NV 3500.

    Object Number: 334324  Size: SH
  65. Install the transmission cover.
  66. Tighten
    Tighten the nut to 12 N·m (106 lb in).

  67. Install the starter. Refer to Starter Motor Replacement in Engine Electrical.

  68. Object Number: 449304  Size: SH
  69. Install the stud holding the bracket for the starter wiring harness and if equipped, the transmission oil cooler lines.
  70. Tighten
    Tighten the bracket stud to 9 N·m (80 lb in).

  71. Install the engine oil cooler pipes. Refer to Engine Oil Cooler Hose/Pipe Replacement in Engine Cooling.
  72. Install the exhaust pipe to the exhaust manifolds. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
  73. Install a NEW oil filter. Refer to Engine Oil and Oil Filter Replacement .
  74. Add engine oil supplement GM P/N 1052367 (Canadian P/N 992869) or equivalent to the engine oil.
  75. Install the underbody shields, if equipped.
  76. Lower the vehicle.

  77. Object Number: 172994  Size: SH
  78. Fill the engine with oil. Refer to Engine Oil and Oil Filter Replacement .
  79. Fill the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  80. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  81. Notice: 

       • Handle the MAF sensor carefully.
       • Do not drop the MAF sensor in order to prevent damage to the MAF sensor.
       • Do not damage the screen located on the air inlet end of the MAF.
       • Do not touch the sensing elements.
       • Do not allow solvents and lubricants to come in contact with the sensing elements.
       • Use a small amount of a soap based solution in order to aid in the installation.


    Object Number: 424556  Size: SH
  82. Install air cleaner outlet duct to throttle body.
  83. Install air cleaner outlet duct to MAF sensor.
  84. Tighten
    Tighten the hose clamp to 4 N·m (32 lb in).


    Object Number: 10940  Size: SH
  85. Connect the intake air temperature (IAT) sensor harness connector.

  86. Object Number: 312278  Size: SH
  87. Install the air cleaner outlet duct retaining wingnut.
  88. Tighten
    Tighten the wingnut to 2 N·m (18 lb in).


    Object Number: 444792  Size: SH
  89. Install the breather tube to the air cleaner outlet duct.
  90. Install the PCV tube to the right valve rocker arm cover and the air cleaner outlet duct.
  91. Recharge the air conditioning system, if equipped. Refer to Refrigerant Recovery and Recharging in Heating, Ventilation, and Air Conditioning.
  92. Install the hood. Refer to Hood Replacement in Body Front End.
  93. With the ignition OFF or disconnected, crank the engine several times. Listen for any unusual noises or evidence that any of the parts are binding.
  94. Start the engine and listen for unusual noises.
  95. Check the vehicle oil pressure gauge or light and confirm that the engine has acceptable oil pressure.
  96. If necessary, install an oil pressure gauge and measure the engine oil pressure.

  97. Operate the engine at about 1,000 RPM until the engine has reached normal operating temperature.
  98. Listen for improperly adjusted or sticking valves, sticking valve lifters, or other unusual noises.
  99. Inspect for oil and/or coolant leaks while the engine is operating.
  100. Verify that the distributor is properly positioned.
  101. Perform a final inspection for the proper engine oil and coolant levels.