GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 8001 Dial Indicator Set
    • J 21777-40 Rear Pilot Washer
    • J 21777-42 Front Pilot Washer
    • J 21777-43 Stud Assembly Bolt
    • J 21777-45 Side Bearing Discs
    • J 21777-1 Arbor
    • J 21777-29 Gage Plate
    • J 21777-35 Rear Pilot Washer
    • J 23597-1 Arbor
    • J 23597-11 Gage Plate

    Important: Make sure all of the tools, the differential side bearing bores, and the pinion bearing cups are clean before proceeding.

  1. Lubricate the pinion bearings with axle lubricant. Refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.
  2. Install the pinion bearings into the axle housing.

  3. Object Number: 651745  Size: SH
  4. Assemble the following components into the axle housing:
  5. • For the 7.6 inch axle, assemble the J 21777-40  (1), the J 21777-43  (2), the J 21777-42  (3), and the J 21777-45  (4) as shown.
    • For the 8.6 inch axle, assemble the J 21777-35 (1), the J 21777-43  (2), the J 21777-42  (3), and the J 21777-29 (4) as shown.
  6. While holding the J 21777-43 stationary, install an inch-pound torque wrench on the nut of the J 21777-43 and tighten the nut until a rotating torque of 2.2 N·m (20 lb in) is obtained.
  7. Rotate the assembly several times in both directions in order to seat the pinion bearings.

  8. Check the rotating torque of the assembly. If the torque is less than 1.7 N·m (15 lb in), tighten the nut on the J 21777-43 until a rotating torque of 1.7-2.8 N·m (15-25 lb in) is obtained.

  9. Object Number: 651746  Size: SH
  10. Assemble the following components into the differential carrier bore of the axle housing:
  11. • For the 7.6 inch axle, assemble the J 21777-45 (1, 2) to the J 23597-1  (3) as shown.
    • For the 8.6 inch axle, assemble the J 21777-45 (1, 2) to the J 21777-1 (3) as shown.
  12. Install the bearing caps.
  13. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  14. Install the bearing cap bolts.
  15. Tighten
    Tighten the bearing cap bolts to 75 N·m (55 lb ft).

  16. Rotate the J 23597-1 (7.6 inch axle) or the J 21777-1 (8.6 inch axle) within the J 21777-45 . The J 23597-1 or the J 21777-1 must rotate back and forth freely within the discs. If the J 23597-1 or the J 21777-1 does not rotate freely, disassemble the components, inspect for proper seating and/or mis-aligned components and re-assemble.

  17. Object Number: 670320  Size: SH
  18. Align the plunger of the J 23597-1 (1) to the J 23597-11 (2) (7.6 inch axle) or the J 21777-1 (1) to the J 21777-29 (2) (8.6 inch axle).
  19. Install the J 8001 to the J 23597-1 or the J 21777-1 as follows:
  20. 11.1. Loosely clamp the J 8001 onto the stem on the J 23597-1 or the J 21777-1.
    11.2. Place the contact pad of the J 8001 onto the mounting post of the J 23597-1 or the J 21777-1.
    11.3. With the contact pad of the J 8001 touching the mounting post of the J 23597-1 or the J 21777-1, loosen the lock nut on the J 8001 and push down on the J 8001 until the needle the J 8001 has turned 3/4 of a turn clockwise.
    11.4. Tighten the clamp on the J 8001 finger tight.
  21. Move the plunger of the J 23597-1 or the J 21777-1 back and forth until the needle of the J 8001 indicates the greatest deflection.
  22. The deflection is the point where the needle changes direction.


    Object Number: 670316  Size: SH
  23. At the greatest point of deflection, move the housing of the J 8001 until the needle indicates zero.
  24. Move the plunger of the J 23597-1 or the J 21777-1 back and forth again to verify the zero setting. Adjust the housing of the J 8001 as necessary to set the needle to zero.
  25. Rotate the plunger of the J 23597-1 from the J 23597-11 (7.6 inch axle) or the J 21777-1 away from the J 21777-29 (8.6 inch axle) until it no longer touches the J 23597-11 (7.6 inch axle) or the J 21777-29 (8.6 inch axle).
  26. The value indicated on the J 8001 is the thickness of the shim needed in order to set the depth of the pinion.
  27. Select the shim that indicates the proper thickness. Measure the shim with a micrometer in order to verify that the thickness is correct.
  28. Remove the pinion depth setting tools.
  29. Remove the pinion bearings.
  30. Install the pinion shim between the pinion gear and the inner pinion bearing. Refer to Drive Pinion Bearings Replacement .