Step | Action | Value(s) | Yes | No | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Fog Lights Schematics | ||||||||||||||||||||||
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |||||||||||||||||||
2 | Verify that the front fog lamps are inoperative. Do the front fog lamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||||||||||||||
3 | Is only one front fog lamp inoperative? | -- | Go to Step 4 | Go to Step 5 | ||||||||||||||||||
4 |
Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
5 | Use the Scan Tool to inspect for the following related Body Control Module (BCM) Data/ Input Parameters and Output Controls. Refer to Scan Tool Data List for typical values and definitions.
Did you find and correct a problem? | -- | Go to Step 20 | Go to Step 6 | ||||||||||||||||||
6 | With the engine Off, turn the key to RUN and the headlamp switch to PARK. Are the park lamps on? | -- | Go to Step 7 | |||||||||||||||||||
7 | Inspect the PARK LP fuse in the underhood fuse block. Is the fuse open? | -- | Go to Step 8 | Go to Step 9 | ||||||||||||||||||
8 | Remove the front fog lamp relay. Using a J 39200 Digital Multimeter (DMM), check for continuity to ground at the battery positive voltage supply circuit terminal of the front fog lamp relay connector in the body relay block. Refer to Electrical Center Identification Views and Circuit Testing in Wiring Systems. Is continuity present? | -- | Go to Step 13 | Go to Step 14 | ||||||||||||||||||
9 |
Is the specified voltage present? | B+ | Go to Step 15 | Go to Step 10 | ||||||||||||||||||
10 | Use the Scan Tool to monitor the front fog lamp switch ON input. Does the scan tool indicate that the switch is ON? | -- | Go to Step 11 | Go to Step 12 | ||||||||||||||||||
11 | Test the front fog lamp supply voltage and the front fog lamp relay control circuits for an open or high resistance. Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 16 | Go to Step 18 | ||||||||||||||||||
12 | Test the front fog lamp switch signal and ground circuits for opens or high resistance. Refer to Circuit Testing in Wiring Systems. Was a problem found? | -- | Go to Step 17 | Go to Step 19 | ||||||||||||||||||
13 | Repair the short to ground in one of the following circuits. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
14 | Repair the short to ground in the front fog lamp supply voltage circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
15 | Repair the open or high resistance in the ground circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
16 | Repair the open or high resistance in one of the following circuits. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
17 | Repair the open or high resistance in one of the following circuits. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
18 | Replace the front fog lamp relay. Refer to Relay Replacement in Wiring Systems. Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
19 | Replace the front fog lamp switch. Refer to Fog Lamp Switch Replacement . Did you complete the repair? | -- | Go to Step 20 | -- | ||||||||||||||||||
20 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 | ||||||||||||||||||
