Circuit Description
Heated oxygen sensors are used to minimize the amount of time required for closed loop fuel control operation and to allow accurate catalyst monitoring. The oxygen sensor heater greatly decreases the amount of time required for fuel control sensors Bank 1 HO2S 1 and Bank 2 HO2S 1 to become active. Oxygen sensor heaters are required by catalyst monitor sensors Bank 1 HO2S 2 and Bank 1 HO2S 3 to maintain a sufficiently high temperature which allows accurate exhaust oxygen content readings further from the engine. The PCM will run the heater test only after a cold start (determined by engine coolant and intake air temperature at the time of startup) and only once during an ignition cycle. When the engine is started the PCM will monitor the HO2S voltage. When the Bank HO2S voltage indicates a sufficiently active sensor, the PCM looks at how much time has elapsed since startup. If the PCM determines that too much time was required for the Bank 1 HO2S 3 to become active, a DTC P0147 will set. The time it should take the HO2S to reach operating temperature is based on the engine coolant temperature at start-up and the average Mass Air Flow since startup (higher average airflow or higher startup engine coolant temperature = shorter time to HO2S activity).
Conditions for Setting the DTC
| • | Intake Air Temperature (IAT) is less than 35°C (95°F) at startup |
| • | Engine Coolant Temperature (ECT) is less than 35°C (95°F) at startup. |
| • | IAT and ECT are within 6°C (11°F) of each other at start-up. |
| • | Average mass airflow for the sample period is less than 20 gm/s. |
| • | Bank 1 HO2S 3 voltage remains within 150 mV of the bias voltage (about 450 mV) for a longer amount of time than it should. The amount of time ranges between 30 seconds and 5 minutes depending on engine coolant temperature at startup and average air flow since startup. |
| • | Throttle position is less than 37% for 3 seconds. |
| • | Engine run time is greater than 3 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Poor connection at PCM - Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Damaged harness - Inspect the wiring harness for damage. If the harness appears to be OK, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the display will indicate the location of the fault. |
Review the Fail Records vehicle mileage since the diagnostic test last failed. This may help determine how often the condition that caused the DTC to be set occurs.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table:
-
The HO2S should be allowed to cool before performing this test. If the HO2S heater is functioning, the signal voltage will gradually increase or decrease as the sensor element warms. If the heater is not functioning, the HO2S signal will remain near the 450 mV bias voltage.
-
This step ensures that the ignition feed circuit to the HO2S is not open or shorted. The test light should be connected to a good chassis ground, in case the HO2S low or HO2S heater ground circuit is faulty.
-
This step checks the HO2S heater ground circuit.
-
This step checks for an open or shorted HO2S heater element. The heater element resistance will vary according to HO2S temperature (a hot HO2S heater element will measure a much higher resistance than a HO2S heater element at room temperature). It is important to allow the HO2S to cool before measuring HO2S heater element resistance.
-
An open HO2S signal or low circuit can cause the HO2S heater to appear faulty. Check these circuits before replacing the sensor.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
|
Important: If engine has just been operating, allow engine to cool for about one half hour before proceeding.
Does HO2S voltage go from bias voltage to greater than the first specified value or less than the second specified value? | 600 mV 300 mV | Go to Diagnostic Aids | ||
3 | Inspect fuse for Bank 1 HO2S 3 ignition feed. Is the fuse open? | -- | ||
Important:: Use a known good ground. Do not use the Bank 1 HO2S 3 heater ground or Bank 1 HO2S 3 low. Does test light illuminate? | -- | |||
Connect the test light between Bank 1 HO2S 3 ignition feed and Bank 1 HO2S 3 heater ground. Does test light illuminate? | -- | |||
Is HO2S resistance within the specified values? | 3-10 ohms | |||
7 | Repair open Bank 1 HO2S 3 ignition feed circuit to Bank 1 HO2S 3. Refer to Heated Oxygen Sensor (HO2S) Repair in Electrical Diagnosis. Is the action complete? | -- | -- | |
8 | Repair open Bank 1 HO2S 3 heater ground circuit. Refer to Heated Oxygen Sensor (HO2S) Repair in Electrical Diagnosis. Is the action complete? | -- | -- | |
9 |
Was a poor connection found? | -- | ||
10 |
Was a problem found? | -- | ||
Check for a poor Bank 1 HO2S 3 signal or low circuit terminal connection at the Bank 1 HO2S 3 harness connector and replace terminal(s) if necessary. Refer toHeated Oxygen Sensor (HO2S) Repair in Electrical Diagnosis. Did any terminals require replacement? | -- | |||
12 | Check for poor Bank 1 HO2S 3 low circuit terminal connection at the PCM and replace terminal if necessary. Refer to Wiring Repairs in Electrical Diagnosis. Did the terminal require replacement? | -- | ||
13 | Check for poor Bank 1 HO2S 3 signal circuit terminal connection at the PCM and replace terminal if necessary. Refer to Wiring Repairs in Electrical Diagnosis. Did the terminal require replacement? | -- | ||
14 | Replace Bank 1 HO2S 3. Refer to Heated Oxygen Sensor Replacement . Is the action complete? | -- | -- | |
15 | Locate and repair short to ground in Bank 1 HO2S 3 ignition feed circuit and replace faulty fuse. Refer to Heated Oxygen Sensor (HO2S) Repair in Electrical Diagnosis. Is the action complete? | -- | -- | |
16 |
Important: If engine has just been operating, allow engine to cool for about one half hour before proceeding.
Does HO2S voltage go from bias voltage to greater than the first specified value or less than the second specified value? | 600 mV 300 mV | System OK | |
