GM Service Manual Online
For 1990-2009 cars only
Table 1: Range Reference Chart
Table 2: TFP Manual Valve Position Switch Logic
Table 3: DTC P1870 Slipping Transmission Component

Object Number: 42275  Size: MF

Range Reference Chart

Range

Gear

1-2 SS Valve

2-3 SS Valve

2-4 Band

Forward Clutch

Forward Sprag Clutch Assembly

3-4 Clutch

OVER DRIVE

2nd

Off

On

Applied

Applied

Holding

--

3rd

Off

Off

--

Applied

Holding

Applied

4th

On

Off

Applied

Applied

--

Applied

Circuit Description

The PCM monitors the difference between engine speed and transmission output speed. In D3 drive range with the TCC engaged, the engine speed should closely match transmission output speed. In D4 drive range with the TCC engaged, TCC slip speed should be between -20 and +20 RPM.

When the PCM detects excessive TCC slip when the TCC should be engaged, then DTC P1870 sets. DTC P1870 is a type A DTC.

Conditions for Setting the DTC

The following conditions are met for three TCC cycles with reported excessive TCC slip conditions:

    • No TP DTCs P0122 or P0123
    • No VSS DTC P0502
    • No TFT sensor DTCs P0172 or P0173
    • No 1-2 SS Valve DTCs P0751 or P0753
    • No 2-3 SS Valve DTCs P0756 or P0758
    • No TFP Valve Position Switch DTC P1810
    • No TCC PWM Solenoid Valve DTC P1860
    • No TCC Solenoid Valve DTC P1864
    • The engine speed is greater than 400 RPM for 8 seconds and not in fuel cutoff.
    • The engine vacuum is 0-106 kPa.
    • The engine torque is 50-500 lb ft.
    • The gear range is D4.
    • Not in 1st gear
    • The TP angle is 9-35%.
    • The TFT is 20-120°C (68-248°F).
    • The TCC is ON for greater than 5 seconds.
    • The TCC is at maximum apply for greater than 5 seconds.
    • The Shift Solenoid performance counter is zero.
    • The TCC slip speed is greater than 175 RPM for 7 seconds.

Action Taken When the DTC Sets

    • The PCM inhibits TCC engagement.
    • The PCM commands maximum line pressure.
    • The PCM inhibits 4th gear if in hot mode.
    • The PCM freezes shift adapts from being updated.
    • The PCM illuminates the Malfunction Indicator Lamp (MIL).

Conditions for Clearing the MIL/DTC

    • The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported.
    • A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported.
    • The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM.

Diagnostic Aids

    • A TFP Valve Position Switch malfunction could set DTC P1870.
    • The following mechanical conditions could set DTC P1870:
       - A mechanical failure of the shift solenoid valves
       - A mechanical failure of the TCC Solenoid Valve
       - A mechanical failure of the TCC PWM Solenoid Valve
    • Internal transmission failures may set a DTC P1870.
    • An engine misfire may erroneously set a DTC P1870.
    • Ensure that the final drive ratio matches the PCM's calibration.
    • A PRNDL DTC may falsely set a DTC P1870.
    • Refer to Range Reference table.

TFP Manual Valve Position Switch Logic

Gear Position

Range Signal A

Range Signal B

Range Signal C

Park

OFF

ON

OFF

Reverse

ON

ON

OFF

Neutral

OFF

ON

OFF

D4

OFF

ON

ON

D3

OFF

OFF

ON

D2

OFF

OFF

OFF

D1

ON

OFF

OFF

Illegal

ON

OFF

ON

Illegal

ON

ON

ON

Test Description

The numbers below refer to the Step numbers on the diagnostic table.

  1. This step compares the indicated range signal to the actual selected range. A faulty TFP Valve Position Switch could set a DTC P1870.

  2. This step tests for slippage while the torque converter is in a commanded lock-up state.

DTC P1870 Slipping Transmission Component

Step

Action

Value(s)

Yes

No

1

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check , Section 6

2

  1. Install the scan tool.
  2. With the engine OFF, turn the ignition switch to the RUN position.
  3. Important:: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. The Clear Info function will erase the data.

  4. Record the DTC Freeze Frame and the Failure Records.
  5. Apply the brake pedal.
  6. Select each transmission range: Low, Dr 2, Dr 3, Overdrive, Reverse and Park.

Refer to the TFP Val. Position Sw. Logic Table.

Does each selected transmission range match the scan tool TFP switch A/B/C display?

--

Go to Step 3

Go to Pressure Switch Assembly Resistance Check

3

Drive the vehicle in 4th gear while the TCC is engaged.

At any time is the TCC Slip Speed greater than the specified value for 7 seconds?

175 RPM

Go to System Diagnosis Charts

Go to Diagnostic Aids