Oxidation Catalytic Converter 5.7L VIN P; Left

1. Raise the vehicle. Suitably support the vehicle. Refer to Section 0A.
2. Disconnect the heated oxygen sensor electrical connector.
3. Disconnect the rosebud clip from the bracket above the starter motor.



4. Remove the heated oxygen sensor from the left side catalytic converter.



5. Remove the nuts attaching the catalytic converter to the exhaust manifold.



6. Remove the bolts that attach the left side catalytic converter to the right side catalytic converter.



7. Remove the left side catalytic converter from the vehicle.

1. Install the left side catalytic converter to the vehicle.



2. Install the bolts that attach the left side catalytic converter to the right side catalytic converter.

Tighten
Tighten the catalytic converter bolts to 25 N·m (18 lb ft).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




3. Install the nuts that attach the left side catalytic converter to the exhaust manifold.

Tighten
Tighten the nuts to 35 N·m (26 lb ft).




4. Install the heated oxygen sensor to the left side catalytic converter.

Tighten
Tighten the heated oxygen sensor to 42 N·m (31 lb ft).

5. Connect the electrical connector. Then, attach the rosebud clip to the bracket above the starter motor.
6. Lower the vehicle.

Oxidation Catalytic Converter 5.7L VIN P; Right

1. Raise the vehicle. Suitably support the vehicle. Refer to Section 0A.
2. Disconnect the heated oxygen sensor electrical connector.
3. Disconnect the rosebud clip from the catalytic converter hanger bracket.



4. Remove the heated oxygen sensor from the right side catalytic converter.



5. Remove the bolts that attach to the left side catalytic converter.



6. Loosen the clamp that attaches the left side catalytic converter to the exhaust pipe.



7. Remove the bolts that attach the catalytic converter hanger to the left side catalytic converter.



8. Remove the right side catalytic converter by sliding the converter out of the exhaust pipe.

1. Install the right side catalytic converter by sliding the converter into the exhaust pipe.



2. Install the bolts that attach the left side catalytic converter to the converter hanger.

Tighten
Tighten the bolts to 41 N·m (30 lb ft).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




3. Install the exhaust crossover pipe nuts that attach the left side catalytic converter to the exhaust manifold.

Tighten
Tighten the crossover pipe nuts to 35 N·m (26 lb ft).




4. Position the clamp.

Tighten
Tighten the clamp bolt to 68 N·m (50 lb ft).




5. Install the bolts that attach the right side catalytic converter to the left side converter.

Tighten
Tighten the converter bolts to 25 N·m (18 lb ft).




6. Install the heated oxygen sensor to the right side catalytic converter.

Tighten
Tighten the heated oxygen sensor to 42 N·m (31 lb ft).

7. Connect the electrical connector.
8. Attach the rosebud clip to the catalytic converter hanger bracket.
9. Lower the vehicle.