DTC U1304 Lost Communication with UART System. Chevrolet Camaro 1998

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1998 🢒 Camaro 🢒 DTC 🢒 DTC U1304 Lost Communication with UART System

ABS Components
ABS/TCS Schematics
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice
OBD II Symbol Description Notice

Circuit Description

The UART serial data line allows information to be exchanged from module to module as needed. This is done by the PCM, the PCM requests and sends all the information that is transmitted on the UART line.

Conditions for Setting the DTC

DTC U1304 can be set anytime the ignition is in the RUN position and the EBTCM does not recieve a $90 message from the PCM for 6 seconds.

Action Taken When the DTC Sets

•	A malfunction DTC stores.

•	The TCS is disabled.

•	The amber TCS indicator is turned on.

Conditions for Clearing the DTC

•	The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.

•	100 ignition cycles pass with no DTC(s) detected.

Diagnostic Aids

•	It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.

•	Thoroughly inspect any circuitry that may be causing the complaint for the following conditions:

-	Backed out terminals

-	Improper mating

-	Broken locks

-	Improperly formed or damaged terminals

-	Poor terminal-to-wiring connections

-	Physical damage to the wiring harness

•	The following conditions may cause an intermittent malfunction:

-	A poor connection

-	Rubbed-through wire insulation

-	A broken wire inside the insulation

•	If an intermittent malfunction exists refer to Troubleshooting Procedures Cell 4 in Electrical Diagnosis for further diagnosis.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

This step checks for a short to ground in CKT 800.

This step checks for a short to battery voltage in CKT 800.

This step checks for an open in CKT 800.

DTC U1304 Lost Communication with UART System

Step	Action	Value(s)	Yes	No
1	Was the Diagnostic System Check performed?	--	Go to Step 2	Go to Diagnostic System Check
2	Turn the ignition switch to the OFF position. Disconnect the EBCM/EBTCM connector C1. Install the J 39700 Universal Pinout Box using the J 39700-530 cable adapter to the EBCM/EBTCM harness connector C1 only. Using J 39200 DMM, measure the resistance between terminals 24 and 15 of J 39700 . Is the resistance within the range specified in the value(s) column?	OL (infinite)	Go to Step 4	Go to Step 3
3	Repair CKT 800 for a short to ground. Refer to Repair Procedures Cell 5 in Electrical Diagnosis. Is the repair complete?	--	Go to Diagnostic System Check	--
4	Turn the ignition switch to the RUN position, engine off. Using J 39200 DMM, measure the voltage at terminal 24 of J 39700 . Is the voltage within the range specified in the value(s) column?	Battery voltage	Go to Step 5	Go to Step 6
5	Repair CKT 800 for a short to battery voltage. Refer to Repair Procedures Cell 5 in Electrical Diagnosis. Is the repair complete?	--	Go to Diagnostic System Check	--
6	Turn the ignition switch to the OFF position. Disconnect the PCM. If the vehicle is equipped with a V8 disconnect the PCM connector C4. If the vehicle is equipped with a V6 disconnect the PCM connector C1. Using J 39200 DMM measure the resistance between the J 39700 terminal 24 and the PCM terminal 30 if the vehicle is equipped with a V8 or terminal 15 if the vehicle is equipped with a V6. Is the resistance within the range specified in the values column?	0-2ohms	Go to Step 8	Go to Step 7
7	Repair CKT 800 for an open. Refer to Repair Procedures Cell 5 in Electrical Diagnosis. Is the repair complete?	--	Go to Diagnostic System Check	--
8	Replace the EBCM/EBTCM. Refer to Electronic Brake Control Module Replacement . Is the replacement complete?	--	Go to Diagnostic System Check	--