GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Camaro 🢒 Engine 🢒 Engine Controls - 3.8L 🢒 Cruise Control Module Replacement

Removal Procedure

    Object Number: 296575 Size: SH
  1. If equipped without traction control, perform the following:
    2. 1.1. Rotate the throttle lever rearward.
    1.2. Push down the cable end to remove it from the throttle lever pin.
    1.3. Using a flat bladed tool, push in the cable retainer at the throttle body bracket.
    1.4. Slide the cruise control cable up from the throttle body bracket.
    1.5. Remove the cruise control cable from under the accelerator/cruise control cable servo bracket.

    Object Number: 296573 Size: SH
  2. If equipped with traction control, unsnap and remove the cruise control servo cable adjuster cover.

    3. Object Number: 296567 Size: SH
  3. If equipped with traction control, perform the following:
    4. 3.1. Rotate the upper cam, and remove the cruise control cable slug from the servo cable adjuster.
    3.2. Unsnap the locking tab and remove the cable from the slot.
  4. Lay the throttle body end of the cruise control cable down near the cruise control module.
  5. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  6. Remove the left front bumper fascia lower deflector. Refer to Front Bumper Fascia Air Deflector Replacement in Bumpers.

    7. Object Number: 520739 Size: SH
  7. Remove the cruise control module bracket bolts.
  8. Remove the cruise control module and bracket from the left side engine compartment outer rail.

    9. Object Number: 296583 Size: SH
  9. Unsnap and remove the cruise control module cover.
  10. Remove the electrical connector retainer.
  11. Disconnect the cruise control module electrical connector.

    12. Object Number: 296582 Size: SH
  12. Remove the cable locking retainer from the module.
  13. Compress the conduit tangs.

    14. Object Number: 296577 Size: SH
  14. Pull the cruise control cable (4) out from the module (2).
  15. Unhook the cable bead (1) from the module ribbon (3).
  16. Lay the module and bracket on a work surface.

    17. Object Number: 296587 Size: SH
  17. Remove the cruise control module to bracket bolts.
  18. Remove the cruise control module from the bracket.

Installation Procedure

    Object Number: 296587 Size: SH
  1. Place the cruise control module onto the bracket.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the cruise control module bolts.

    3. Tighten
    Tighten the cruise control module bolts to 5 N·m (44 lb in).


    Object Number: 296577 Size: SH
  3. Inspect the cable end to insure that the O-ring is in place.
  4. Pull the throttle body end of the cable until cable is taut, continue to hold while performing the following:
    5. 4.1. Hook the cable bead (1) to the module ribbon (3).
    4.2. Rotate the cable end if necessary, to straighten the ribbon.
    4.3. Push the cable fitting end over the ribbon.
    4.4. Snap the cable end into the module.
    4.5. Ensure that the conduit tangs are engaged.

    Object Number: 296582 Size: SH
  5. Install the cable locking retainer to the module.

    6. Object Number: 296583 Size: SH
  6. Connect the cruise control module electrical connector.
  7. Install the electrical connector retainer.
  8. Align the cruise control module cover over the cable and bracket.

    9. Object Number: 520743 Size: SH
  9. Snap the cover closed over the flanges on the bracket.

    10. Object Number: 520739 Size: SH
  10. Install the cruise control module and bracket to the left side engine compartment outer rail.
  11. Install the cruise control module bracket bolts.

    12. Tighten

        • Tighten the cruise control module bracket bolts to the rail to 10 N·m (89 lb in).
        • Tighten the cruise control module bracket bolt to 2 N·m (18 lb in).
  12. Route the throttle body end of the cruise control cable up to the throttle body.
  13. Instal the left front bumper fascia lower deflector. Refer to Front Bumper Fascia Air Deflector Replacement in Bumpers.
  14. Lower the vehicle.

    15. Object Number: 296567 Size: SH
  15. If equipped with traction control, perform the following:
    16. 15.1. Rotate the upper cam, and install the cruise control cable slug to the servo cable adjuster.
    15.2. Slide the cable onto the slot, ensure locking tab is snapped into position.

    Object Number: 296573 Size: SH
  16. Slide the cruise control servo cable adjuster cover down and snap into place.

    17. Object Number: 296575 Size: SH
  17. If equipped without traction control, perform the following:
    18. 17.1. Rotate the throttle lever rearward.
    17.2. Snap the cruise control cable end to the throttle lever.
    17.3. Align cable and slide onto slot, locking tab must be snapped into position.
  18. Adjust the cruise control cable as needed. Refer to Cruise Control Cable Adjustment .