High Mount Stop Lamp Replacement Chevrolet

1. Remove the high mount stop lamp screws.
2. Remove the liftgate window trim panel. Refer to Liftgate Trim Panel Replacement in Body Rear End.



3. Disconnect the high mount stop lamp connector from the electrical harness.



4. Remove the high mount stop lamp from the rear end spoiler.

1. Position the high mount stop lamp to the rear end spoiler.



2. Connect the high mount stop lamp connector to the electrical harness.
3. Install the liftgate window finishing lace. Refer to Liftgate Trim Panel Replacement in Body Rear End.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the high mount stop lamp screws.

Tighten
Tighten the high mount stop lamp screws to 2 N·m (18 lb in).

High Mount Stop Lamp Replacement Pontiac

1. Remove the high mount stop lamp screws.
2. Remove the liftgate window finishing lace. Refer to Liftgate Trim Panel Replacement in Body Rear End.



3. Disconnect the high mount stop lamp connector from the electrical harness.



4. Remove the high mount stop lamp from the rear end spoiler.

1. Position the high mount stop lamp to the rear end spoiler.



2. Connect the high mount stop lamp connector to the electrical harness.
3. Install the liftgate window finishing lace. Refer to Liftgate Trim Panel Replacement in Body Rear End.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the high mount stop lamp screws.

Tighten
Tighten the high mount stop lamp screws to 2 N·m (18 lb in).

High Mount Stop Lamp Replacement Chevrolet Convertible

1. Remove the high mount stop lamp screws.
2. Open the rear compartment.
3. Remove the rubber access plug located in the center of the trunk inner.



4. Pull the wires through the access hole until the connector is reached.
5. Remove the foam tape from the connector.
6. Disconnect the high mount stop lamp electrical connector.
7. Remove the high mount stop lamp.

1. Position the high mount stop lamp to the rear spoiler.
2. Connect the high mount stop lamp electrical connector.
3. Install foam tape 3M™ P/N 6380 or equivalent around the connector.
4. Push the wires into the access hole.
5. Install the rubber access hole cover.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Install the high mount stop lamp screws.

Tighten
Tighten the high mount stop lamp screws to 2 N·m (18 lb in).

High Mount Stop Lamp Replacement Pontiac Convertible

1. Remove the high mount stop lamp screws.
2. Open the rear compartment.
3. Remove the rubber access plug located in the center of the rear compartment.



4. Pull the wires through the access hole until the connector is reached.
5. Remove the foam tape from the connector.
6. Disconnect the high mount stop lamp electrical connector.
7. Remove the high mount stop lamp.

1. Position the high mount stop lamp to the rear compartment lid.
2. Connect the high mount stop lamp electrical connector.
3. Install foam tape 3M™ 6308 or equivalent around the connector.
4. Push the wires into the access hole.
5. Install the rubber access hole cover.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Install the high mount stop lamp screws.

Tighten
Tighten the high mount stop lamp screws to 2 N·m (18 lb in).